Vacon NX ACTIVE FRONT END II Applications Manual Download

Page: 25 / 94

Arfiff05 Standard AFE-II

vacon •

Local contacts: http://drives.danfoss.com/danfoss-drives/local-contacts/

V1.2.9

Current [A]

ID1113

Total unfiltered current

V1.2.10

Drive Power

[kW] ID 1508

Drive input terminal electrical power.

V1.2.11

Fault History

ID37

Last active fault. If drive has several fault at the same time see from fault history w hat
was the first fault.

V1.2.12

Final DC Ref

[%]

ID1131

Final DC Reference, including offset control.

V1.2.13

Cabin State Word

ID1884

Cabin State Word ID1884

Fault

Fault Codes

Main Fuse

W81

Aux voltage

W82

STO Fuse

W83

Insulation Fault

W84

Earthswitch Fault

W85

Arc Relay

W86

high Amb Temp.

W88

Leakage

W89

Not used

b10

Not used

b11

Not used

b12

Not used

b13

Not used

b14

Not used

b15

Not used

Summary of Contents for NX ACTIVE FRONT END II































































































Search results

Summary of Contents for NX ACTIVE FRONT END II

Reviews:

Related manuals for NX ACTIVE FRONT END II

Brands by name

Popular brands

Vacon NX ACTIVE FRONT END II, Applications Manual

Search results

Summary of Contents for NX ACTIVE FRONT END II

Reviews:

Related manuals for NX ACTIVE FRONT END II

Brands by name

Popular brands