Vacon NX ACTIVE FRONT END II Applications Manual Download Page 59

Page: 59 / 94

Arfiff05 Standard AFE-II

vacon •

Local contacts: http://drives.danfoss.com/danfoss-drives/local-contacts/

This parameter sets the time constant of the controller for the active current of the
regenerative unit (15 equals 1.5ms).

P2.6.7.8

Synch. Kp Start

ID1300

P2.6.7.9

Voltage Control Kp

ID1451

This parameter sets the gain for the DC link PI voltage controller.

P2.6.7.10 Voltage Control Ti

ID1452

This parameter sets the time constant in ms of the DC link PI controller.

P2.6.7.11 Switching frequency

ID601

The switching frequency of the IGBT bridge in kHz. Changing the default value may
impact on the LCL filter operation.

Summary of Contents for NX ACTIVE FRONT END II































































































Search results

Summary of Contents for NX ACTIVE FRONT END II

Reviews:

Related manuals for NX ACTIVE FRONT END II

Brands by name

Popular brands

Vacon NX ACTIVE FRONT END II, Applications Manual

Search results

Summary of Contents for NX ACTIVE FRONT END II

Reviews:

Related manuals for NX ACTIVE FRONT END II

Brands by name

Popular brands