UTC Fire and Security Interlogic NetworX NX-7002N, Installation Manual

Page: 36 / 55

NX-7002N Installation Manual Page 36 05/06/13
To Do This Send This Explanation Example
Arm your system arm [ partition list ] Arms the system remotely.
Instead of the partition
numbers you can use a
keyword ALL for all
partitions. arm 1 to arm partition 1
arm 1 3 to arm partitions 1 and 3
arm all to arm all partitions
Disarm your system disarm [ partition list ] Disarms the system
remotely. disarm 1 to disarm partition 1
disarm 1 3 to disarm partitions 1 and
3
disarm all to disarm all partitions
Partarm your system partarm [ partition list ] Partarms the system
remotely. partarm 1 to arm partition 1
partarm 1 3 to arm partitions 1 and 3
partarm all to arm all partitions
Get the status of the specified
zones zone status [ partition list ] Sends the status of the
zone (s) to your phone
(open and bypassed
zones). Sending a
command without a
partition list returns
information for all
partitions. zone status 1 to receive the message
with zone status from zones assigned
to partition 1
zone status all to receive the
message with zone status for all zones
Get a list of zones with
problems zone faults [ partition list ] Sends a list of zones with
problems to your phone.
Sending a command
without a partition list
returns information for all
partitions. zone faults 1 to receive fault
information from zones assigned to
partition 1
zone faults all to receive the message
with zone faults for all zones
Bypass zones bypass [ zone list ] Bypasses the specified
zones. bypass 1 3 to bypass zones 1 and 3
Read events from the event
log events [ number ]
events [ range ]
Sends the specified event
or events from the event
log to the phone. events 1 to read the last (newest)
event from the panel log
events 1 3 to read the last 3 events
from the panel log
events returns the 10 most recent
events
Set a connection to a home
automation device output [ output_number
X10_house_code X10_unit ]
Connects a specified
home automation device. output 2 A 1 to set output two to
control X-10 device with house code A
and unit number 1
Switch on X-10 outputs on [ output list ] Switches on an X-10
output. on 1 4 7 to switch on X-10 outputs 1, 4
and 7
on all to switch on all X-10 outputs
Switch off X-10 outputs off [ output list ] Switches off an X-10
output. off 1 4 7 to switch off X-10 outputs 1, 4
and 7
off all to switch off all X-10 outputs
Activate an auxiliary function switch aux [ output list ] Changes the auxiliary
function that occurs when
it is activated, for example
by a button on a keyfob. switch aux 1 to activate aux output 1
on the panel
Change your user code user code [ new user code ] Changes your user code. user code 0101 to change your own
user code to 0101
Change another user code user code [ user number new
user code ]
Changes another persons’
user code. user code 2 0101 to change the user
code to 0101 for the user 2
Delete a user code delete user code [ user
number ]
Deletes a user code. delete user code 2 to delete the user
code for the user 2
Start reporting start reporting Sends reports from the
NX7002. start reporting
Stop reporting until system re-
arm stop reporting Stops reports being sent
form the NX7002 until the
system is rearmed. stop reporting
Stop reporting until you start it
again stop reporting permanent Stops reports being sent
from the NX7002 until the
start reporting command is
sent. stop reporting permanent
Register your phone register [ phone number user
number ]
The phone is registered
with your alarm system. register 32444123456 2 to register
the number 32444123456 to user 2
Register your phone with a
new password register [ phone number user
number Password ]
The phone is registered
with your alarm system register 32444123456 1 444444 to
register the number 32444123456 to