Utax CD 1016 Instruction Handbook Manual Download Page 99

Page: 99 / 122

Section 8 TROUBLESHOOTING

8-5

Grasp the Left Cover handles to lift the cover and open it.

Remove jammed sheets of paper carefully so as not to tear
them.

Note

If the paper is torn, be sure to remove all remnants or
fragments from the drawer.

If the Duplex Unit (option) is installed, lift it up and remove
the paper.

Note

If the paper is torn, be sure to remove all remnants or
fragments from the drawer.

Close the front cover.

Paper misfeed in the Document Processor
(option)

(J70, J71, J72, J73, J74, J75)

When the paper misfeed location is lit as shown in the illustration
below, the paper misfeed has occurred in the optional Document
Processor. Use the procedure below to clear it.

Inch specifications

Metric specifications

If there are originals on the Original Table, remove them.

Open the Left Cover.

CAUTION

The fixation section inside the main unit of the

copier is extremely hot. Exercise caution in

handling it to prevent getting burned.

Summary of Contents for CD 1016



























































































































Search results

Summary of Contents for CD 1016

Reviews:

Related manuals for CD 1016

Brands by name

Popular brands

Utax CD 1016, Instruction Handbook Manual

Search results

Summary of Contents for CD 1016

Reviews:

Related manuals for CD 1016

Brands by name

Popular brands