Utax CD 1016 Instruction Handbook Manual Download Page 84

Page: 84 / 122

Section 6 COPIER MANAGEMENT

6-28

Rotate Sort Setting

Set whether or not to change the direction for each copy set and
sort it when sorting copies.

Display the Default Settings Mode. (Refer to P.6-11

"Default Settings Mode Operations Procedures"

Inch

specifications

Metric

specifications

Press either the Zoom (+) or Zoom

(–)

key to display “F30”.

Inch

specifications

Metric

specifications

Press the [OK] key.

Inch

specifications

Metric

specifications

Press either the Zoom (+) key or the Zoom

(–)

key and select

“on” to change the direction for each copy set and sort it or
“oFF” to sort in the same direction.

Inch

specifications

Metric

specifications

Press the [OK] key.
The display will return to that of Step 2.

Inch specifications

Metric specifications

Silent Mode Transition Time

Shortens the amount of time the internal motor continues to run
after the copy is produced. Use this setting in cases when the motor
noise is bothersome.

Display the Default Settings Mode. (Refer to P.6-11

"Default Settings Mode Operations Procedures"

Inch specifications

Metric specifications

Press either the Zoom (+) or Zoom

(–)

key to display “F31”.

Inch specifications

Metric specifications

Press the [OK] key.

Inch specifications

Metric specifications

Summary of Contents for CD 1016



























































































































Search results

Summary of Contents for CD 1016

Reviews:

Related manuals for CD 1016

Brands by name

Popular brands

Utax CD 1016, Instruction Handbook Manual

Search results

Summary of Contents for CD 1016

Reviews:

Related manuals for CD 1016

Brands by name

Popular brands