urmet domus elekta Manual Download Page 3

sec.3g 

−−−−

 

3

2 VOICE - Technical Manual

ELEKTA AND ELEKTA STEEL CALL MODULE

2VOICE ELEKTA CALL MODULE Ref. 1083/15 (50Hz) – 1083/25 (60Hz)

2VOICE ELEKTA STEEL CALL MODULE Ref. 1083/16 (50Hz) – 1083/27 (60Hz)

INSTALLATION Ref. 1083/15 - 108 3/25

INSTALLATION Ref. 1083/16 - 1083/27

INSTALLATION Ref. 1083/15 - 1083/25

Arrange the duct so that it ends at the lower holes of the 

fl

 ush-

mounting box. 

Embed the 

fl

 ush-mounting body Ref. 1145/53 at the given 

height.

1,55

÷

1,60 m / 5.08

÷

5.25 ft

294 mm / 11.57"

45 mm

1.77"

118 mm

4.65"

(1,40 m / 4.59 ft)

(*) 

For disabled or special needs users of the D1 type (elderly) and D2 

type (lower limb motor dif

fi

 culties), 

the centre of the device

 must 

be arranged at a height comprised between 75 cm and 140 cm with 

respect to the 

fl

 oor. For more details, see technical standard CEI 

64-21:2016-12 – Residential environments. Systems suited for use 

by people with disabilities or special needs.

Establish the electric connections (see speci

fi

 c paragraph).

Fix the calling module to the 

fl

 ush-mounting box with the screws 

provided. Complete the calling module with the 

fi

 nishing  frame, 

which is 

fi

 xed using two Torx ® screws.

INSTALLATION Ref. 1083/16 - 1083/27

Arrange the duct so that it ends at the lower hole of the 

fl

 ush-

mounting box.

Remove the lower cap from the wire hole (1).

Apply adhesive labels on the holes for the screws of the frame 

(2).

Install 

fl

 ush-mounting box Ref. 1158/43 at indicated height (3).

Fix the frame to the 

fl

 ush-mounting body (4).

Establish the electric connections.

Fix the calling module to the frame (4).

ALTO

TOP
HAUT

A

ALTO
TOP
HAUT

B

ALTO

TOP
HAUT

1,55

÷

1,60 m / 5.08

÷

5.25 ft

298 mm / 11.73"

45 mm

1.77"

118 mm / 4.65"

(1,40 m / 4.59 ft)

1

3

2

(*) 

For disabled or special needs users of the D1 type (elderly) and D2 

type (lower limb motor dif

fi

 culties), 

the centre of the device

 must 

be arranged at a height comprised between 75 cm and 140 cm with 

respect to the 

fl

 oor. For more details, see technical standard CEI 

64-21:2016-12 – Residential environments. Systems suited for use 

by people with disabilities or special needs.

ELECTRIC CONNECTIONS

Refer to the information contained in the system manual for 

more information on wiring, maximum distances and reference 

wiring diagrams.

The call module is provided with an extractable terminal board to 

facilitate connection operations.

§

Summary of Contents for elekta





















Reviews: