36
DS4091-002
37
DS4091-002
•
Press the
button to end after you hear the Service not active message confi rming that the service is not
active.
To check the function:
•
Press 3F followed by F2.
•
Wait for the confi rmation message and press the button
to end.
The icon
will light up on the display to indicate that the divert service is on.
6.11 EXTERNAL DIVERT TO PRIVATE LINE
This function is used to immediately divert all calls routed to your extension to a previously programmed
external number using another telephone line confi gured as private (DISA must be enabled). The switchboard
dials the programmed telephone number and connects the two lines. A specifi c number can be programmed
for each extension. This connection lasts for 60 seconds and can be extended by pressing any DTMF during
the last 5 seconds of connection (a tone will be heard). A “divert” tone will be heard when the function is
active when you pick up the handset. The telephone can be used to make calls in any case.
Press
∗∗∗
to end the call.
To switch the function on:
•
Press 2F followed by F3.
•
Dial L and wait for the “service on” message, where:
L =
80
for any available private line.
81 ÷ 86 for line 1 ÷ 6
87 ÷ 89 for basic interface 1 ÷ 3
74
for basic interface 4
•
Press the
button to end.
To switch the function off:
•
Press 3F followed by F3.
•
Press the
button to end after you hear the “Service not active” message confi rming that the service is
not active and press the button to end.
To check the function:
•
Pick up the handset and wait for the dial tone.
•
Dial #672 and wait for the message indicating state of the service.
•
Hang up.
The message “incorrect command” will be heard if you attempt to activate the function on a non-private line
or without programming the number where to divert the call.
6.12 CALL DIVERT TO PRIVATE LINE
It can be used to divert external calls not routed to a specifi c extension after the fi fth ring towards a previously
programmed external number using another telephone line confi gured as private (DISA enabling is required).
The switchboard dials the programmed telephone number and connects the two lines. This connection lasts
for 60 seconds and can be extended by pressing any DTMF during the last 5 seconds of connection (a tone
will be heard). A “divert” tone will be heard when the function is active when you pick up the handset. The
telephone can be used to make calls in any case.
Press
∗∗∗
to end the call.
To switch the function on:
•
Press 2F followed by F4.
•
Dial L and wait for the “service on” message, where:
L =
80
for any available private line.
81
÷ 86 for line 1 ÷ 6
87 ÷ 89 for basic interface 1 ÷ 3
74
for basic interface 4
•
Press the
button to end.
To switch the function off:
•
Press 3F followed by F4.
•
Press the
button to end after you hear the “Service not active” message confi rming that the service is
not active and press the button to end.
To check the function:
•
Pick up the handset and wait for the dial tone.
•
Dial #662 and wait for the message indicating state of the service.
•
Hang up.
The message “incorrect command” will be heard if you attempt to activate the function on a non-private line
or without programming the number where to divert the call.
6.13 CAPTURE CALL TO ANSWERING MACHINE OR FAX
The call capture function is used to route an established communication to an answering machine terminal
or a fax machine as required by the device making the request.
To activate the function:
•
Press 2F followed by dedicate button F12.
