Upright X Series Service & Parts Manual Download Page 22

Page: 22 / 164

Page 2-10

Operation and Specifications

2.5 - Maintenance

X Series Work Platform

2.5 M

AINTENANCE

Figure 2-9: Blocking the Elevating Assembly

LOCKING

LEVATING

SSEMBLY

NSTALLATION

1. Park the work platform on a firm, level surface.

2. Pull Chassis Emergency Stop Switch to the ON

position.

3. Pull Platform Emergency Stop Switch to the ON

position.

4. Turn and hold the Chassis Key Switch to CHASSIS.

5. Push the Chassis Lift/Lower Switch to LIFT to ele-

vate the platform until the Scissor Brace can be
rotated to the vertical position.

6. X20N, X20W, and X26N - From rear of the machine,

lift the Scissor Brace from its stowed position.
Rotate upward and outward, then down until it is
hanging vertically below its attachment point.

7. X31N - From the left side of the machine, pull the

locking pin securing the brace. Rotate the Scissor
Brace counterclockwise until it is in the vertical
position.

8. Lower the platform by pushing the Chassis Lift/

Lower Switch to LOWER and gradually lower the
platform until the Scissor Brace is supporting the
platform.

EMOVAL

1. Using the Chassis Controls, gradually elevate the

platform until the Scissor Brace is clear.

2. X20N, X20W, and X26N - Rotate the Scissor Brace

outward and upward over its mounting point until it
rests in the stowed position.

3. X31N - Rotate the Scissor Brace clockwise until the

locking pin engages.

4. Lower the platform by pushing the Chassis Lift/

Lower Switch to LOWER to completely lower the
platform.

W A R N I N G

Never perform service while the platform is elevated without first blocking the
elevating assembly.

DO NOT stand in the elevating assembly area while deploying or storing brace.

DO NOT block the elevating assembly with a load on the platform.

PIN RESTS ON

BRACE WHEN IN

BLOCKING POSITION

SCISSOR BRACE

IN REST POSITION

BRACE ROTATES

TO BLOCKING

POSITION

BRACE RESTS ON

PIN WHEN IN

BLOCKING POSITION

X20N, X20W, and X26N

X31N

BRACE RESTS ON

WELDMENT WHEN IN

BLOCKING POSITION

ROTATE BRACE

CLOCKWISE

TO BLOCK

060571-005

Summary of Contents for X Series





































































































































































Search results

Summary of Contents for X Series

Reviews:

Related manuals for X Series

Brands by name

Popular brands

Upright X Series, Service & Parts Manual

Search results

Summary of Contents for X Series

Reviews:

Related manuals for X Series

Brands by name

Popular brands