Upright X Series Service & Parts Manual Download Page 25

Page: 25 / 164

Page 2-13

Operation and Specifications

2.5 - Maintenance

X Series Work Platform

FRONT

REAR

FRONT

LEFT MODULE

RIGHT MODULE

061787-001

DANGER

OF PLATFORM BEFORE OPERATING MACHINE.

THIS BAR MUST BE PINNED IN POSITION ACROSS END

X31N Platform

MAXIMUM SIDE LOAD 200 LBS.

OR 4 OCCUPANTS

PLATFORM LOAD 1000 LBS.

MAXIMUM DISTRIBUTED

WARNING

101250-003

MAXIMUM SIDE LOAD 150 LBS.

OR 3 OCCUPANTS

PLATFORM LOAD 1000 LBS.

MAXIMUM DISTRIBUTED

WARNING

101250-004

MAXIMUM SIDE LOAD 150 LBS.

OR 3 OCCUPANTS

PLATFORM LOAD 700 LBS.

MAXIMUM DISTRIBUTED

WARNING

101250-005

MAXIMUM SIDE LOAD 113 LBS.

OR 2 OCCUPANTS

PLATFORM LOAD 750 LBS.

MAXIMUM DISTRIBUTED

WARNING

101250-002

1600 LBS.

WHEEL LOAD

MAXIMUM

101252-004

1750 LBS.

WHEEL LOAD

MAXIMUM

101252-005

1850 LBS.

WHEEL LOAD

MAXIMUM

101252-006

EMERGENCY

DOWN VALVE

LOWER PLATFORM

PULL KNOB TO

DANGER

TIP-OVER HAZARD

MAXIMUM DISTRIBUTED LOAD

250 LBS. OR 1 OCCUPANT

ON EXTENDED DECK

MAXIMUM SIDE LOAD 100 LBS.

061220-002

1 Required

066560-010

1 Required

X20W, X26N, X31N

066560-011

1 Required

X20N

066555-000
1 Required

060197-000
1 Required

066554-000
1 Required

066554-000

1 Required

066550-000
1 Required

061787-001
1 Required
X31N

066558-000
1 Required
X20N, X20W, X26N

005223-003
1 Required
X31N

014222-003-99
2 Required

101250-004

2 Required

X26N

101250-005

2 Required

X31N

101250-002

2 Required

X20N

101250-003

2 Required

X20W

061205-005
1 Required

066522-000
1 Required

066559-000

1 Required

101252-004

1 Required

X20N, X20W

101252-005

1 Required

X26N

101252-006

1 Required

X31N

066561-002

1 Required

X31N

066556-000
2 Required

066561-000

1 Required

X20N, X20W, X26N

101251-000
1 Required

005221-000

1 Required

062562-001

1 Required

066553-000
2 Required

066556-001

4 Required

066552-000

1 Required

010076-001
1 Required

107051-000
1 Required

1999

NOTE:

Labels can be ordered by using Part Number located by each label. For machines equipped with options

consult the Service Manual.

Proper label installation is required. All of these labels shall be present and in

good condition before operating the work platform. Be sure to read, under-

stand, and follow these labels BEFORE operating the work platform.

060571-005

Summary of Contents for X Series





































































































































































Search results

Summary of Contents for X Series

Reviews:

Related manuals for X Series

Brands by name

Popular brands

Upright X Series, Service & Parts Manual

Search results

Summary of Contents for X Series

Reviews:

Related manuals for X Series

Brands by name

Popular brands