Upright X Series Service & Parts Manual Download Page 50

Page: 50 / 164

Page 3-22

Maintenance

3.17 - Lift Cylinder

X Series Work Platform

Figure 3-26: Lift Cylinder Assembly

NSTALLATION

1. Attach a suitable hoisting device and sling to the cylinder. Carefully position the cylinder in

the Elevating Assembly and install the upper Pivot Pin.

2. On X20 machines, make sure the Locking Pin fully engages the pivot and pin. Install the

retaining ring.

3. On X26N machines, install a new roll pin.

4. Carefully lift the cylinder and align the lower mount and install the Pivot Pin. Make sure the

locking pin is properly installed, then install the retaining ring.

5. Connect the Emergency Lowering Valve cable and Down Valve wires.

6. Unplug hydraulic hoses and attach to the cylinder. Replace hydraulic fluid removed from the

Lift Cylinder.

7. Test with weight at rated platform load to check system operation. Check for leaks and level

of fluid.

A. Rod
B. Thread Cap Head
C. Piston
D. Barrel
E. Bronze Bushings
F. Set Screw
Seal Kit Part Number 066601-010

A.   Rod
B.   Thread Cap
C.   Thread Cap Head
D.   Piston
E.   Thin Locknut
F.   Barrel
G.   Bronze Bushings
H.   Set Screw

Seal Kit Number 066618-101
1.   Uniring
2.   Back-up Ring
3.   O-Ring
4.   O-Ring
5.   Back-up Ring
6.   Loaded U-Cup
7.   Rod Wiper

Lift Cylinder Assembly for X20W, X26N, and the lower cylinder of the X31N

Lift Cylinder Assembly for X20N and the upper cylinder of the X31N

060571-005

Summary of Contents for X Series





































































































































































Search results

Summary of Contents for X Series

Reviews:

Related manuals for X Series

Brands by name

Popular brands

Upright X Series, Service & Parts Manual

Search results

Summary of Contents for X Series

Reviews:

Related manuals for X Series

Brands by name

Popular brands