Upright X Series Service & Parts Manual Download Page 56

Page: 56 / 164

Page 4-2

Troubleshooting

4.2 - Troubleshooting

X Series Work Platform

4.2 T

ROUBLESHOOTING

1. Verify your problem.

• Do a full function test from both the platform and chassis controls, and note all functions that

are not operating correctly.

2. Narrow the possible causes of the malfunction.

• Use the troubleshooting guide to determine which components are common to all circuits

that are not functioning correctly. To aid in troubleshooting, the letters following the compo-
nent on the table are the same as the component’s designation on the schematics.

3. Identify the problem component.

• Test components that are common to all circuits that are not functioning correctly. Remem-

ber to check wires and terminals between suspect components. Be sure to check connec-
tions to battery negative.

4. Repair or replace any component found to be faulty.

5. Verify that repair is complete.

• Do a full function test from both the platform and chassis controls to verify that all functions

are operating correctly and that the machine is performing to specified values.

PECIAL

OOLS

Following is a list of tools which may be required to perform certain maintenance procedures on
the X Series Work Platforms.

• Flow Meter with Pressure Gauge

(UpRight P/N 067040-000)

•

0-69 bar (

0-1000 psi

(0-69 bar

) Hydraulic Pressure Gauge with Adapter Fittings (UpRight P/

N 014124-010)

•

0-207 bar (

0-3000 psi

(0-207 bar

) Hydraulic Pressure Gauge with Adapter Fittings (UpRight

P/N 014124-030)

• Adapter Fitting (UpRight P/N 063965-002)

• Inclinometer (UpRight P/N 010119-000)

• Crimping Tool (UpRight P/N 028800-009)

• Terminal Removal Tool

(UpRight P/N 028800-006)

DJUSTMENT

ROCEDURES

Figure 4-1: Hydraulic Test Port

Hydraulic settings must be checked whenever a com-
ponent is repaired or replaced.

Remove counterbalance valves and "bench test" them
if they are suspect.

Connect a pressure gauge of appropriate range to the
test port located on the hydraulic manifold.

Correct pressure settings are listed in the hydraulic
schematic.

HECKING

UMP

RESSURES

Remove hose from pump port and connect pressure tester.

Test Port

060571-005

Summary of Contents for X Series





































































































































































Search results

Summary of Contents for X Series

Reviews:

Related manuals for X Series

Brands by name

Popular brands

Upright X Series, Service & Parts Manual

Search results

Summary of Contents for X Series

Reviews:

Related manuals for X Series

Brands by name

Popular brands