Upright X Series Service & Parts Manual Download Page 33

Page: 33 / 164

Page 3-5

Maintenance

3.5 - Supporting Elevating Assembly

X Series Work Platform

X31N

Figure 3-6: Blocking the Elevating Assembly--X31N

NSTALLATION

1. Park the work platform on a

firm, level surface.

2. Verify that both Emergency

Stop Switches are ON.

3. Turn the Chassis Key Switch to

CHASSIS.

4. Push the Chassis Lift Switch to

UP, and elevate the platform
approximately 9 Ft. (2.7 m),
leaving enough room to freely
rotate the Scissor Brace.

5. Pull out on the retaining pin,

and rotate the Scissors Brace
into the vertical position.

6. Push the Chassis Lift Switch to the DOWN position, and gradually lower the platform until

the upper and lower pivot pins rest on the Scissor Brace.

EMOVAL

1. Push the Chassis Lift Switch to the UP position and gradually raise the platform until the

Scissor Brace will clear the pivot pins.

2. Rotate the Scissor Brace counterclockwise until it locks into position parallel with the scissor

arm.

3. Push the Chassis Lift Switch to the DOWN position, and completely lower the platform.

060571-005

Summary of Contents for X Series





































































































































































Search results

Summary of Contents for X Series

Reviews:

Related manuals for X Series

Brands by name

Popular brands

Upright X Series, Service & Parts Manual

Search results

Summary of Contents for X Series

Reviews:

Related manuals for X Series

Brands by name

Popular brands