United Electronic Industries PD2-MF User Manual Download Page 61

Page: 61 / 152

Chapter 3: Architecture

User Counter-Timer
Subsystem

User counter-timer is based on the Intel 82C54 16-bit counter-timer
chip. It contains three fully independent counter-timers. It’s fully

dedicated for user applications and it is not used by any of the
PowerDAQ systems. The logic allows you to select the clock and gate

source for each of the three independent counter-timers. The counter-
timer outputs can generate interrupts to the host PC on change of

their state.

You can feed a clock input from one of the following four sources:

•

Software command

•

1-MHz internal timebase

•

External clock input line

•

UCT0 output line (available for UCT1 and 2)

Gate can be controlled from two sources

•

Software command

•

External gate input line

Each of the UCT can be used in following modes:

•

"Pulse" - generates one pulse with value/frequency length

(Mode 1)

•

"Train" - generates pulse train with value/frequency rate.

Pulse length is 1/frequency (Mode 2)

•

"Rate" - generates pulse train with value/frequency rate.

Pulse length is 1/2 value/frequency high and 1/2

value/frequency low (Mode 3)

•

"Delay" - waits value/frequency time and then generates

one pulse (Mode 5)

See Intel 82C54 datasheet and PowerDAQ SDK examples for
implementation details.

Summary of Contents for PD2-MF

























































































































































Search results

Summary of Contents for PD2-MF

Reviews:

Related manuals for PD2-MF

Brands by name

Popular brands

United Electronic Industries PD2-MF, User Manual

Search results

Summary of Contents for PD2-MF

Reviews:

Related manuals for PD2-MF

Brands by name

Popular brands