United Electronic Industries PD2-MF User Manual Download Page 60

Page: 60 / 152

Chapter 3: Architecture

Latch configuration is a 16-bit word, two bits for each one of eight
sense inputs.

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

F R F R F R F R F R F R F R F R

F: 1 in this position, the inputs are sensitive to falling edge

R: 1 in this position, the inputs are sensitive to rising edge

Table 23: Digital Input Configuration Word

The Edge Detector and Latch Logic detect configured edges on the

digital input lines. A 8-bit latch register has 1 bit per input line. It is set
to “1” when the configured edge is detected. Additionally, the logic

fires an interrupt to the DSP to inform it when the configured
conditions are met.

If you set up a latch configuration to watch for edges on several lines,

the interrupt fires as soon as any of the selected conditions happen.
However, the interrupt will not be re-fired again until the user

application clears the bit. If a change is detected on another line, the
interrupt will re-fire. To recognize which line caused an interrupt you

have to read the digital input status (i.e. latch register).

Summary of Contents for PD2-MF

























































































































































Search results

Summary of Contents for PD2-MF

Reviews:

Related manuals for PD2-MF

Brands by name

Popular brands

United Electronic Industries PD2-MF, User Manual

Search results

Summary of Contents for PD2-MF

Reviews:

Related manuals for PD2-MF

Brands by name

Popular brands