background image

 
 
 

25 

 

The content of this manual may not be reproduced in any form without 

the permission of the manufacturer.

 

 

Our  products  are  patented  and  their  trademarks.  The  manufacturer 

reserves  the  right  to  change  specifications  and  prices  if  this  is  due  to 

technological improvements.

 

 

 

ASSISTANCE

 

 

If  the  instrument  does  not  operate  properly,  before  contacting  the 

Customer Service, check the status of the battery and wear of the cables 

and  replace  them  if  necessary.  If  the  instrument  continues  to  manifest 

malfunctions check if the procedure of use of the same is  in accordance 

with what is indicated in this manual. If the instrument is to be returned to 

the  after  -  sales  service  or  to  a  dealer  transportation  is  borne  by  the 

customer. The shipment must, however, be agreed. Attached to dispatch an 

explanatory  note  about  the  reasons  of  the  instrument  must  always  be 

inserted. For shipping only use the original packaging; any damage caused 

by the use of non-original packing shall be charged to the customer.

 

 
 
 
 
 
 
 
 
 

Summary of Contents for C6





























Reviews: