Unify OpenScape Desk Phone IP 55G User Manual Download | Manualshive

Page: 237 / 267

background image

Call recording

237

Call recording

A central voice recorder (voice recorder from

) is installed in the network for

recording calls to which your telephone connects in order to record the current
voice traffic. The recorder records the entire voice flow of two or more partici-
pants.

You should configure a recording button in order to simplify handling of manual
call recording

Page 92. It is assumed in the description below that a corre-

sponding key has been configured.

Recording modes

The administrator can configure the following operating modes for call record-
ing:
• Manual
• AutoStart
• All Calls
• Disabled

The following settings are possible to audibly signal the recording:
• Repeated
• Single Shot
• Off

Check with your administrator as to which settings were made for your phone.

Mode: ALL CALLS

The telephone starts and stops the recorder automatically in order to ensure that
all calls are being recorded.

Mode: MANUAL

You decide when the recorder is started and stopped or paused. If the recorder
is switched on, all further calls will be recorded. If you pause the recorder then
nothing will be recorded. If there are no calls, then the recorder likewise pauses.

Mode: AUTOSTART

The telephone starts the recorder automatically. You can stop or pause the re-
corder yourself however and restart it. If a call has already been recorded, new
incoming and outgoing calls will also be recorded. If you pause the recorder dur-
ing a call, special calls such as consultation calls, call pickups and second calls
will not be recorded as long as the recorder is paused. If the telephone reverts
to idle status, the AutoStart process is set up again for the next call.

«
...
235
236
237
238
239
...
»

Summary of Contents for OpenScape Desk Phone IP 55G












































































































































































































































































Reviews:

No comments

Related manuals for OpenScape Desk Phone IP 55G

Brand: Gigaset Pages: 27

Brand: Kyocera Pages: 32

Brand: TCL Pages: 74

Brand: Alcatel Pages: 10

Brand: STK Professional Audio Pages: 1

Brand: NEG Pages: 10

Brand: Amplicomms Pages: 90

Brand: myPhone Pages: 50

Brand: Aastra Pages: 163

STUDIO ENERGY 2

Brand: Blu Pages: 20

Brand: Cellacom Pages: 22

Brand: NUU Mobile Pages: 16

Brand: switel Pages: 4

SGH-T519 - Trace Cell Phone

Brand: Samsung Pages: 141

Brand: Samsung Pages: 178

Brand: Samsung Pages: 174

Brand: Samsung Pages: 105

Brand: Hisense Communications Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands