background image

iii

LIST OF FIGURES (CONT)

Page

Figure 2-5.  SYSTEM WITH MULTIPLE RECEIVERS AND VIDEO SWITCHER......2-19

Figure 3-1.  Mother Board Indicators............................................................................3-2

Figure 3-2.  Expansion Board Indicators ......................................................................3-4

Figure A-1.  TYPICAL INSTALLATION FOR CRX-500 SERIES RECEIVER WITH

OPTION B1 OR B2 INSTALLED............................................................. A-2

Figure A-2.    OPTION B1 OR B2  INSTALLATION .................................................... A-4

LIST OF DRAWINGS

Installation, CRX-501 Pan & Tilt Receiver NEMA 1 (Indoor) (D/N 517584-1440)  .....2-31

Installation, CRX-510 Pan & Tilt Receiver NEMA 4 (Outdoor) (D/N 517584-5440)....2-32

Installation, CRX-510/220/X Pan & Tilt Receiver NEMA 4 (Outdoor)
220 Vac Input, 220 Vac Pan & Tilt (D/N 517584-9440) .............................................2-33

Installation, CRX-502 Pan & Tilt Receiver NEMA 1 (Indoor) (D/N 517588-1440) ......2-34

Installation, CRX-502/220/X Pan & Tilt Receiver NEMA 1 (Indoor)
(D/N 517588-9440).....................................................................................................2-35

Installation, CRX-520 Pan & Tilt Receiver NEMA 4 (Outdoor) (D/N 517588-5440)....2-36

LIST OF TABLES

Table 2-1.  CAMERA NUMBERS ...............................................................................2-11

Table 2-2.  CRX-500 RECEIVER TO PAN AND TILT UNIT.......................................2-24

Summary of Contents for CRX-501


































































Reviews: