manualshive.com logo in svg

UBI ScanPlus 1800, Installation Manual

Share
Download
UBI ScanPlus 1800 Installation Manual Download Page 34

5. Set up the data transmission parameters

 

SP/XX/IG/12/E/980228

5-6

  RS-232

  Additional parameters—ScanPlus Reference Manual

baud rate - 75 - 150 - 300 - 600 - 1200 - 2400 - 4800 -

38400

hardware/software protocols timeout - 1000 ms (*)

- unlimited
- user-defined 1 to 2500 ms

ENQ (Hex 05) - not used (*)

- ENQ (HEX 05)
- user-defined

ACK (Hex 06) - not used (*)

- ACK (HEX 06)
- user-defined

NAK (Hex 15) - not used (*)

- NAK (HEX 15)
- user-defined

XON/XOFF software protocol - not active (*)

- active

LRC (longitudinal redundancy check) - not active (*)

- active

preamble - no preamble

- user-defined

postamble - user-defined

"code mark" symbology identifiers - not transmitted (*)

- transmitted
- default / user-defined

AIM symbology identifiers - not transmitted (*)

transmitted

inter-character delay - 20 - 30 - 40 - 50 ms

- user-defined 1 to 999 ms

inter-message delay - none (*)

- 10 - 30 - 50 - 80 - 100 ms
- user-defined 1 to 999 ms

Summary of Contents for ScanPlus 1800

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands