U-Line OHAUS DEFENDER 5000 Manual Download Page 9

PAGE 9 OF 33 

1219 IH-8105

OPERATION CONTINUED

NOTE: If the Security Switch is set to ON, the 

Capacity Unit, Range, Capacity, Graduation 
and Power On Zero settings are not reset.

READOUT MENU

Enter this menu to customize display functionality. 

NOTE: Default settings are in bold.

STABILITY

Set the amount the reading can vary before the stability 

symbol turns off.

0.5d  

= 0.5 scale division

1d

  

= 1 scale division

2d  

= 2 scale divisions

5d  

= 5 scale divisions

ZERO RANGE

Set the percentage of scale capacity to be zeroed.

2%

100%

NOTE: The setting is forced and locked to 2% 
when security switch is set to the locked position.

FILTER LEVEL

Set the amount of signal filtering.

Low  

=  faster stabilization time with less  

stability

Medium

   =  normal stabilization time 

with normal stability

High  

=  slower stabilization time with  

 

more stability

AUTO ZERO TRACKING

Set the automatic zero tracking functionality.

OFF  

= Disabled.

 0.5  division

   =  Display will maintain zero until 

a change of 0.5 divisions per 

second is exceeded.

1d  

=  Display will maintain zero until  

a change of one division per 

second is exceeded.

3d   

=  Display will maintain zero until 

a change of three divisions per 

second is exceeded.

AUTO DIM

Set the display backlight functionality.
Settings:

1 min

  

=  Backlight turns off after one 

minute of inactivity.

2 min  

=  Backlight turns off after two 

minutes of inactivity.

5 min  

=  Backlight turns off after five 

minutes of inactivity.

10 min  

=  Backlight turns off after 10 

minutes of inactivity.

Always on
Off

SCREENSAVER

Set whether the screensaver is enabled after the 

selected time period.

Off  

= Disabled.

5 min

  

=  Screensaver is enabled after 

five minutes.

10 min  

=  Screensaver is enabled after 

10 minutes.

30 min  

=  Screensaver is enabled after 

30 minutes.

AUTO OFF

Set whether the display enters sleep mode after the 

selected time period.

Off 

 

= Disabled.

5 min  

=  Display enters sleep mode after 

five minutes.

10 min  

=  Display enters sleep mode after  

10 minutes.

30 min  

=  Display enters sleep mode after  

30 minutes.

READOUT

OPTIONS

Stability

0.5d, 

1d

, 2d, 5d

Zero Range

+/-2%, 

+/-100%

Filter Level

Low, 

Medium

, High

Auto Zero Track

Off, 

0.5d

, 1d, 3d

Backlight

Off, 

1min

, 2min, 5min, 10min, Always On

Screensaver

Off, 

5min

, 10min, 30min

Auto Off

Off

, 5min, 10min, 30min

Adjust Contrast

1, 2, 

3

,

 

4, 5

Reset

Summary of Contents for OHAUS DEFENDER 5000


































Reviews: