TZ Centurion 7130CF Product Manual Download Page 5

Page: 5 / 35

page 2 of 11

A TZ Business |

ixp.tz.net

, TZ Centurion

™

, TZ SlideHandle

™

, TZ Radial

™

, TZ SMArt

™

and TZ Sensors

™

are trademarks of TZ Limited. Patents Pending.

TZ Centurion

™

Bridge

TZ Centurion

™

Bridge Model 7130CF Series

1.3 Contents of the Standard Package

The TZ Centurion Bridge 7130CF comes complete with the

following items:

TZ Centurion

™

Bridge 7130CF

SDHC 2Gb card

Quick Start Guide

TZ Centurion Bridge 7130 Series Product Manual

TZ Device Discovery Application

SNMP MIB file

Adobe

Acrobat Reader

Product Registration Information

1.4 System Example

Figure 2 shows an example of a TZ network system that may

be used to control and monitor multiple computer racks and

provide access to authorised parties when warranted.

The TZ network allows an administrator — on or off-site — to

monitor and control cabinets and other areas secured with

TZ intelligent locks and devices.

Each of these components is controlled by the TZ Centurion

Bridge, allowing activity and measurement by any device in

the network to be viewed on the embedded administration

web interface.

Structured Cable

TZ Centurion

™

Bridge

TZ Centurion

™

Port

Link

TZ Centurion

™

Weigand Translator

TZ SlideHandle

™

TZ Sensor

™

Network

Third Party

Card Reader

TZ SwingHandle

™

TZ Centurion

™

Server

Network

Figure 2: TZ Centurion

™

Bridge System

Summary of Contents for Centurion 7130CF




































Search results

Summary of Contents for Centurion 7130CF

Reviews:

Related manuals for Centurion 7130CF

Brands by name

Popular brands

TZ Centurion 7130CF, Product Manual

Search results

Summary of Contents for Centurion 7130CF

Reviews:

Related manuals for Centurion 7130CF

Brands by name

Popular brands