TZ Centurion 7130CF Product Manual Download Page 22 | Manualshive

Page: 22 / 35

background image

page 19 of 11

A TZ Business |

ixp.tz.net

| © 2015

TZ

®

, TZ Centurion

™

, TZ SlideHandle

™

, TZ Radial

™

, TZ SMArt

™

and TZ Sensors

™

are trademarks of TZ Limited. Patents Pending.

TZ Centurion

™

Bridge

TZ Centurion

™

Bridge Model 7130CF Series

8. Configuring TZ Network Devices (Network)

During the first log in session, and any time a new device is added to the network, the TZ Centurion

™

Bridge must be instructed

to discover the device within its network. This is done by clicking on the “Start Discovery” button found under the Settings

subtab of the System tab – as shown below in Figure 14.

Once this is done, go back to the Device Config tab and click the “Edit” button to display a screen that allows specific settings

to be edited for each specific device as explained in the next sections.

Figure 14: The Start Discovery button tells the TZ Centurion

™

Bridge to check for new devices on its own RS-485 network

«
...
20
21
22
23
24
...
»

Summary of Contents for Centurion 7130CF




































Reviews:

No comments

Related manuals for Centurion 7130CF

Express Ethernetwork DI-704P

Brand: D-Link Pages: 17

Brand: D-Link Pages: 10

Brand: 3xLogic Pages: 2

Brand: H3C Pages: 22

Brand: H3C Pages: 3

Brand: Konig Pages: 73

Brand: Falcon Pages: 24

EonServ 5000 Series

Brand: Surveon Pages: 33

RabbitCore RCM4400W

Brand: Rabbit Pages: 126

ControlPoint 2000

Brand: 4Home Pages: 20

Brand: Lanner Pages: 59

Brand: ADIC Pages: 140

Brand: Zhone Pages: 53

Brand: Ruckus Wireless Pages: 4

Brand: R3 Pages: 48

EonStor GS 3000 Series

Brand: Infortrend Pages: 134

FrameSaver SLV NNI

Brand: Paradyne Pages: 20

Brand: TP-Link Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands