TZ Centurion 7130CF Product Manual Download Page 33

Page: 33 / 35

page 30 of 11

A TZ Business |

ixp.tz.net

, TZ Centurion

™

, TZ SlideHandle

™

, TZ Radial

™

, TZ SMArt

™

and TZ Sensors

™

are trademarks of TZ Limited. Patents Pending.

TZ Centurion

™

Bridge

TZ Centurion

™

Bridge Model 7130CF Series

Appendix 1: Specifications

Specifications Overview

Specifications subject to change to suit particular application requirements.

specifica

Specifica

physical

Dims: 17

Weight:

Mounting

CAUTION

This prod
in which

environm

Operating

Storage t

Humidity

Non com

Ingress p

electrica

Supply vo

Power us

1 x Ether

2 x Dry C

2 x Conta

SD card

RS-485 m

RJ-45 pin

standard

FCC Part

RoHS co

dimensio

ations overvi

ations subject t

and mountin

73mm x 110m

540 g (1.2 lbs

g: Screws thro

duct should no

it is mounted.

mental and pe

g temperature

temperature:

(operating): 9

bustible

protection: IP

oltage: 12/24V

sage: 1W (do

rnet Port, Pow

Contact output

act Closure au

port

multi-drop com

n out: 1: +Com

ds complianc

t 15 Class B, C

ompliant, One

ons (mm)

to change to s

ngs

mm x 28mm (6

ough bottom

ot be installed

Do not drill o

erformance

e: -15°C to +5

-55°C to +85°

95% RH at 50

VDC

oes not include

wer-over-Ether

ts, 32VDC 5A

uxiliary inputs

mmunications

ms, 2: -Coms,

CE, IC, and U

Year Limited

siness |

ixp.t

suit particular

.8” x 4.3” x 1.1

in a way that

or otherwise pr

55°C (+5°F to

°C (-67°F to +

0°C (122°F)

e connected d

rnet IEEE 802

interface via R

, 3 & 4: Not Us

UL all in progre

Warranty

tz.net

| © Te

112345.01_D

application re

1”)

compromises

roduce metal s

+131°F)

185°F)

evices)

.3af

RJ-45

sed, 5: Gnd, 6

ess

lezygology, I

quirements.

the Ingress P

shavings arou

6 & 7: Not Use

Centuri

Model N

Inc. 2011

Protection (IP)

und electronic

ed, 8: +V

ion™ B

Number: 7

rating of the e

equipment.

ridge

7130CF

enclosure

Physical And Mountings
>

Dims: 173mm x 110mm x 28mm (6.8” x 4.3” x 1.1”)

Weight: 540 g (1.2 lbs)

Mounting: Screws through bottom

CAUTION:

This product should not be installed in a way that

compromises the Ingress Protection (IP) rating of the

enclosure in which it is mounted. Do not drill or otherwise

produce metal shavings around electronic equipment.

Environmental and Performance
>

Operating temperature: -15°C to +55°C (+5°F to +131°F)

Storage temperature: -55°C to +85°C (-67°F to +185°F)

Humidity (operating): 95% RH at 50°C (122°F)

Non-combustible

Ingress protection: IP 21

Electrical
>

Supply voltage: 12/24VDC

Power usage: 1W (does not include connected devices)

1 x Ethernet Port, Power-over-Ethernet IEEE 802.3af

2 x Dry Contact outputs, 32VDC 5A (Active when powered

with external 24V DC power supply only)

2 x Contact Closure auxiliary inputs

SD card port

RS-485 multi-drop communications interface via RJ45

RJ45 pin out: 1: +Coms

2: -Coms, 3 & 4:

Not Used

5: Gnd

6 & 7: Not Used

8: +V

Standards Compliance
>

FCC Part 15 Class B, CE, UL (c-us) per IEC/UL/CSA 60950-1

RoHS compliant

One Year Limited Warranty

Dimensions (mm)

Summary of Contents for Centurion 7130CF




































Search results

Summary of Contents for Centurion 7130CF

Reviews:

Related manuals for Centurion 7130CF

Brands by name

Popular brands

TZ Centurion 7130CF, Product Manual

Search results

Summary of Contents for Centurion 7130CF

Reviews:

Related manuals for Centurion 7130CF

Brands by name

Popular brands