TZ Centurion 7130CF Product Manual Download Page 28

Page: 28 / 35

page 25 of 11

A TZ Business |

ixp.tz.net

, TZ Centurion

™

, TZ SlideHandle

™

, TZ Radial

™

, TZ SMArt

™

and TZ Sensors

™

are trademarks of TZ Limited. Patents Pending.

TZ Centurion

™

Bridge

TZ Centurion

™

Bridge Model 7130CF Series

8.5.3. Firmware Update

Clicking this button will bring up a screen where binary files

containing new firmware and/or new web pages can be

uploaded. The binary files will end in “.tar” and are made

available by TZ as new software releases and updates.

If the .tar file contains additions to the web UI, the user will

be guided through additional screens that reload the new

webpage into the browser.

If the .tar file contains new operating firmware, the device

will automatically beep and reboot after a few seconds to

organize the data internally.

8.5.4. Clear Event Logs

Clicking this button will clear all of the event logs from non-

volatile memory.

8.5.5. Clear Alarm Logs

Clicking this button will clear all of the alarm logs from non-

volatile memory.

8.5.6. Clear Sensor Logs

Clicking this button will clear all of the data of the specified

sensor from non-volatile memory.

9. Event and Alarm Logs

An “event” occurs every time a TZ Radial or TZ SlideHandle

is opened or closed, an RFID is swiped (even if it does not

open anything), or if any user / RFID information has been

added or changed. An “alarm” is a test or condition that is

defined using the different sensors within the network —

and the alarms themselves are defined in the “Alarm Config”

tab discussed in Section 0. Both events and alarms are

displayed in the “Event Logs” tab shown below in 19.

Figure 19: The most recent events and alarms are presented under the Event Logs tab.

Summary of Contents for Centurion 7130CF




































Search results

Summary of Contents for Centurion 7130CF

Reviews:

Related manuals for Centurion 7130CF

Brands by name

Popular brands

TZ Centurion 7130CF, Product Manual

Search results

Summary of Contents for Centurion 7130CF

Reviews:

Related manuals for Centurion 7130CF

Brands by name

Popular brands