TZ Centurion 7130CF Product Manual Download Page 8

Page: 8 / 35

page 5 of 11

A TZ Business |

ixp.tz.net

, TZ Centurion

™

, TZ SlideHandle

™

, TZ Radial

™

, TZ SMArt

™

and TZ Sensors

™

are trademarks of TZ Limited. Patents Pending.

TZ Centurion

™

Bridge

TZ Centurion

™

Bridge Model 7130CF Series

The rear panel of the unit (shown in Figure 4) has the

following connections:

One power port that accepts a 2.1 mm center positive

24V barrel plug from a compatible DC power supply

Two 32VDC 5A auxiliary output dry contact switch

connections.

Two contact closure auxiliary inputs.

One reset switch.

One SDHC card slot used for additional logging and

data storage capability. (The unit supports full size SDHC

cards up to 2GB – no adapters or micro SD cards.)

TZ SlideHandle and TZ Radial

™

Intelligent locks, TZ

Centurion Wiegand Translators and RFID Readers, and other

devices are all plugged into any of the eight RJ45 ports on

the face of the unit. Devices may be connected to the

TZ Centurion Bridge with up to 100 meters of standard

Cat 5e/6 cable.

More than one device can be connected to any leg that

emanates from the TZ Centurion Bridge by daisy-chaining

the connection through the use of TZ Centurion Port Link

or Multi Port Link devices. If the device is farther than 100m

from the TZ Centurion Bridge, it may be necessary to use

a TZ Centurion Multi Port Link in order to connect a power

supply physically closer to the device. If the TZ Centurion

Bridge is powered via PoE (Power over Ethernet), then the

maximum distance without additional power is 7m.

DC Power

Auxillary Output

and Inputs

SD Card Slot

Reset

Figure 4: TZ Centurion

™

Bridge rear connections for power,

auxiliary analog sensors, auxiliary dry contact outputs, reset

button and slot for an additional SDHC card

4. Connecting Devices

Summary of Contents for Centurion 7130CF




































Search results

Summary of Contents for Centurion 7130CF

Reviews:

Related manuals for Centurion 7130CF

Brands by name

Popular brands

TZ Centurion 7130CF, Product Manual

Search results

Summary of Contents for Centurion 7130CF

Reviews:

Related manuals for Centurion 7130CF

Brands by name

Popular brands