Tuthill M-D Pneumatics 7010 Operator'S Manual Download Page 22

Page: 22 / 72

6.8 RECOMMENDED SHUTDOWN PROCEDURE TO MINIMIZE RISK OF FREEZING OR

CORROSION

When high humidity or moisture is present in an air piping system, condensation of water can occur after

the booster is shut down and the booster begins to cool. This creates an environment favorable to corrosion

of the iron internal surfaces, or in cold weather, the formation of ice. Either of these conditions can close the

operating clearances, causing the booster to fail upon future start-up.

The following shutdown procedure outlined below minimizes the risk of moisture condensation, corrosion

and freezing.

NOTE

Care must be taken so as not to overload or overheat the booster during

this procedure.

1. Isolate the booster from the moist system piping, allowing the booster to intake atmospheric air. Operate

the booster under a slight load allowing the booster to heat within safe limits. The heat generated by the

booster will quickly evaporate residual moisture.

2. For carpet cleaning applications, after the work is completed, simply allow the booster to run a few (3-5)

minutes with the suction hose and wand attached. The suction hose and wand will provide enough load

to the booster to evaporate the moisture quickly.

3. For extended shutdown, inject a small amount of a light lubricating oil such as 3-in-One

or a spray

lubricant such as WD-40

into the inlet of the booster just prior to shutdown.

(3-in-One and WD-40 are

registered trademarks of WD-40 Company.)

The lubricant will provide an excellent protective coating

on the internal surfaces. If using a spray lubricant, exercise care to prevent the applicator tube from

getting sucked into the booster. The applicator tube will damage the booster, most likely to the point

that repair would be required.

4. If the booster is being taken out of commission for an extended period of time, please also refer to the

“Long Term Storage”

section of this manual.

7. MAINTENANCE

7.1 GENERAL

Regular inspection of your vacuum booster and its installation, along with complete checks on operating

conditions will pay dividends in added life and usefulness. Also, service the drive per manufacturer’s

instructions and lubricate the coupling or check belt drive tension. By use of thermometers and gauges,

make sure that booster operating temperature and pressure remwain within allowed limits.

DANGER

The booster and parts may contain hazardous media. Assure that pump

and parts are evacuated of hazardous media prior to servicing.

Summary of Contents for M-D Pneumatics 7010









































































Search results

Summary of Contents for M-D Pneumatics 7010

Reviews:

Related manuals for M-D Pneumatics 7010

Brands by name

Popular brands

Tuthill M-D Pneumatics 7010, Operator'S Manual

Search results

Summary of Contents for M-D Pneumatics 7010

Reviews:

Related manuals for M-D Pneumatics 7010

Brands by name

Popular brands