TURFCO WIDESPIN 1540 TEC Operator'S Manual Download Page 10

Page: 10 / 72

85816

Assembly and Installation of the WideSpin 1540 TEC Broadcast Top Dresser

to the Cushman/Textron Turf-Truckster

To Avoid Serious Injury, Avoid Accidental Engine

Starting By Removing the Key From the Trucks

Ignition.

Work Safely and Always wear the Appropriate

Safety Gear.

Read and Understand this Entire Installation

Manual Before

Mounting the WideSpin 1540 TEC.

Read and Understand the Entire Operator’s

Manual For the Cushman Textron Turf Truckster

Before Operating.

Read and Understand All Safety Warnings and

Decals in the manual and on the machine.

Safety on the job should always be a top priority.

Training and experience are important factors in the

safe operation of tools and equipment. Be trained and

familiar with the tools used to install the Mounting Kit.

Work in a clean dry work area. If using electrically

powered equipment, check for proper grounding.

Safety First!!

To Avoid Serious Injury,

Never Attempt To Lift the Top Dresser Manually.

Serious Bodily Injury Could Result From Lifting

The Top Dresser By Hand.

The Weight And Balance Of The Machine

Requires Approved Hoists And Lifting Devices.

The Top Dresser weighs 308.4 Kg (680 lbs) when

empty. Ensure that the hoist or lifting device, and its

rigging are rated to safely lift and suspend the weight

of the top dresser. The hopper of the top dresser must

be empty when the machine is lifted. Never attempt

to install or remove a top dresser that is ﬁlled with

top dressing material. DO NOT attempt to connect or

disconnect any hydraulic connections with the trucks

engine or hydraulic system operating.

Refer to the Cushman Textron

Turf Truckster operator’s

manual for additional safety

warnings!!

Recognizing Safety Warnings Used In Manual

LOOK FOR THE SAFETY HAZARD WARNING SYMBOL

The symbol is used to alert the operator of safety hazards.

It is used in conjunction with the words DANGER, WARNING, and CAUTION.

“DANGER” identifies immediate hazards which will result in serious injury or death.

“WARNING” identifies potential hazards which could result in serious injury or death.

“CAUTION” identifies hazardous situations which may result in minor injury and/or could result in

damage or destruction of equipment.

WARNING

CAUTION

DANGER

WARNING

ASSEMBLY AND INSTALLATION

Summary of Contents for WIDESPIN 1540 TEC









































































Search results

Summary of Contents for WIDESPIN 1540 TEC

Reviews:

Related manuals for WIDESPIN 1540 TEC

Brands by name

Popular brands

TURFCO WIDESPIN 1540 TEC, Operator'S Manual

Search results

Summary of Contents for WIDESPIN 1540 TEC

Reviews:

Related manuals for WIDESPIN 1540 TEC

Brands by name

Popular brands