Tuchel PLUS 560 Operating Manual Download Page 30

Page: 30 / 102

Coupling and uncoupling the sweeper

4-24

4.2

Installation of Sweeper PLUS 560

WARNING

Danger of crushing or impact of persons can occur if persons are present
between vehicle and sweeper during coupling and uncoupling.

Instruct persons to leave the danger area between the vehicle and the
sweeper before moving in front of the sweeper.

Any helpers present may only be positioned next to carrier vehicle to give
directions and are only allowed to step between vehicle and sweeper when
both have come to a full standstill.

WARNING

Danger through failure of the energy supply between vehicle and
sweeper can occur due to damaged supply lines.

Pay attention to the run of the supply lines when coupling the lines. The supply
lines:

•

must easily adapt to all movements without tension, bending or rubbing,

•

must not rub against other parts.

WARNING

Danger due to crushing, dragging -in, catching and impact for persons
can occur if the sweeper inadvertently separates from the vehicle.

•

Note the maximum permissible support loads, towing and axle loads of
the vehicle.

•

Make proper use of the equipment provided for connecting vehicle
and sweeper.

•

Before starting to move with the sweeper coupled, check whether the
quick-release unit of the four-point mounting frame is correctly locked.

Summary of Contents for PLUS 560







































































































Search results

Summary of Contents for PLUS 560

Reviews:

Related manuals for PLUS 560

Brands by name

Popular brands

Tuchel PLUS 560, Operating Manual

Search results

Summary of Contents for PLUS 560

Reviews:

Related manuals for PLUS 560

Brands by name

Popular brands