Tuchel PLUS 560 Operating Manual Download Page 7 | Manualshive

Page: 7 / 102

background image

General

1-3

NOTE

1

General

The present operating instructions are valid for the Sweeper PLUS 560.

1.1

Intended applications

The Sweeper PLUS 560 is designed for the attachment to wheel loaders and construction
machinery.

Because of its robust construction and the various working widths, this sweeper is suited for
permanent use on roads and paths.

The Sweeper PLUS 560 can be mounted via the mechanically or hydraulically operated
quick hitch unit of the respective carrier vehicle, fitting a pallet fork arm into fork pockets,via
an A-frame or a three-point linkage.

The basic version of the Sweeper PLUS 560 comes as a simple sweeping model (without dirt
hopper) and is therefore suitable for cleaning large paved areas.

The various items of additional equipment, such as the dirt hopper with an integrated 3rd
support wheel, the water-spraying system for dust binding, one or two side brushes for
sweeping near edges, a hydraulical lateral adjustment in order to facilitate operation, extra
strong guide rollers, side marker lights and warning flags, permit adaptation to different
working environments.

1.2

Information on the product

1.2.1

Manufacturer's address

Tuchel Maschinenbau GmbH
Holsterfeld 15
D-48499 Salzbergen
Phone: +49 (0)5971 9675-0
Fax: +49 (0)5971 9675-30
E-mail: [email protected]
Spare parts: [email protected]

1.2.2

Descriptive label

The descriptive label can be found on the nameplate.

Model

Serial No.

Build-year / Job No.
Max. operating pressure
[bar]
Max. oil flow [l/min]

Weight [kg]

The overall descriptive label (nameplate, safety
label, etc.) has the status of a certificate. It must
not be changed or rendered illegible and must
be replaced if damaged or missing.

.

«
...
5
6
7
8
9
...
»

Summary of Contents for PLUS 560







































































































Reviews:

No comments

Related manuals for PLUS 560

SNOW ELECTRIC 45

Brand: Stiga Pages: 81

Brand: Little Wonder Pages: 54

Brand: Thermador Pages: 28

Brand: GMP Pages: 62

Brand: Poulan Pro Pages: 22

Brand: MTD Pages: 24

Brand: Craftsman Pages: 23

Brand: Craftsman Pages: 14

Brand: Craftsman Pages: 20

Brand: Craftsman Pages: 13

Brand: Craftsman Pages: 32

Brand: Craftsman Pages: 16

Brand: Craftsman Pages: 16

Brand: Craftsman Pages: 13

Brand: Craftsman Pages: 28

Brand: Craftsman Pages: 20

Brand: Craftsman Pages: 28

Brand: Craftsman Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands