Tuchel PLUS 560 Operating Manual Download Page 24

Page: 24 / 102

Safety information

2-18

Order number and explanation

Warning instructions

40000340

Read and observe the operating manual and
safety instructions before using the sweeper.

40000342

When lowering the vehicle, keep at a
sufficient distance!

•

Instruct persons and animals to leave the
hazard area.

•

Wait until all movable parts of the sweeper
are inactive before reaching into the danger
point.

40000343

Do not enter the slewing area during
operation!

•

Warn persons and animals out of the
hazard area.

•

Wait until all movable parts of the sweeper
are inactive before reaching into the
danger point.

40000338

Danger of cutting or loss of finger and hand
caused by accessible, moving working tools!

This danger can result in serious injuries with
loss of body parts.

•

Never reach into the danger point as long as
the engine is running with hydraulic system
connected.

•

Wait until all movable parts of the sweeper
are inactive before reaching into the danger
point.

Summary of Contents for PLUS 560







































































































Search results

Summary of Contents for PLUS 560

Reviews:

Related manuals for PLUS 560

Brands by name

Popular brands

Tuchel PLUS 560, Operating Manual

Search results

Summary of Contents for PLUS 560

Reviews:

Related manuals for PLUS 560

Brands by name

Popular brands