TT electronics AB Connectors ABCIRP Series Assembly And Wiring Instructions Download Page 5

Page: 5 / 41

AB Connectors Limited

Specification No. 528

ABCIRP Connector Series

Assembly and wiring Instructions

AB Connectors Limited Issue 9: July 2010

Page 5 of 41

1.1.11 Screen termination is simplified by using one of a range of back shell/accessory

combinations.

1.1.12 In summary, the ABCIRP modular bayonet coupling connector offers several

advantages to the user.

•

Metal clip retained removable crimp contacts.

•

Positive lock location of contacts.

•

Circlip retained removable insulator allowing for angular re-positioning.

•

Rapid coupling and uncoupling. 120° rotation of th e coupling nut.

•

Vibration resistant -loosening of the coupling nut under vibration or shock condition is
prevented.

•

Inter-matable and interchangeable with other Mil-C-5015 bayonet types.

Summary of Contents for AB Connectors ABCIRP Series










































Search results

Summary of Contents for AB Connectors ABCIRP Series

Reviews:

Related manuals for AB Connectors ABCIRP Series

Brands by name

Popular brands

TT electronics AB Connectors ABCIRP Series, Assembly And Wiring Instructions

Search results

Summary of Contents for AB Connectors ABCIRP Series

Reviews:

Related manuals for AB Connectors ABCIRP Series

Brands by name

Popular brands