TT electronics AB Connectors ABCIRP Series Assembly And Wiring Instructions Download Page 30

Page: 30 / 41

AB Connectors Limited

Specification No. 528

ABCIRP Connector Series

Assembly and wiring Instructions

AB Connectors Limited Issue 9: July 2010

Page 30 of 41

Contact Size &

Type

Part Number

Wire CSA

Sq.mm

Tool Setting Crimp Tool Turret/ Locator Tool Position

Insertion

tool

Extraction

Tool

100/60 Pin

ABBP10060KPKP80

N/A

D55E/D51

MRP31038

N/A

P80 8 ETA

100/60 Skt

ABBP10060KSKP80

100 Pin

ABBP100KPKP80

MRP0925

100 Skt

ABBP100KSKP80

8/40

ABBP8/40KPKP80

MRP31042

8/40

ABBP8/40KSKP80

8/16

ABBP8/16KPKP80

0.93/1.50

Consult
Factory

M310

Consult
Factory

8/16

ABBP8/16KSKP80

0.93/1.50

ABBP8KPKP80

N/A

ERMA19600

22390

N/A

ABBP8KSKP80

Table of P80 Contact Tooling Data

Summary of Contents for AB Connectors ABCIRP Series










































Search results

Summary of Contents for AB Connectors ABCIRP Series

Reviews:

Related manuals for AB Connectors ABCIRP Series

Brands by name

Popular brands

TT electronics AB Connectors ABCIRP Series, Assembly And Wiring Instructions

Search results

Summary of Contents for AB Connectors ABCIRP Series

Reviews:

Related manuals for AB Connectors ABCIRP Series

Brands by name

Popular brands