Tritium Veefil-RT 175-S Installation Manual Download Page 24

Page: 24 / 25

Veefil-RT 175-S Site Installation Manual

TRI125.INS.018 version 1

4 March 2020

Manual

Page 24 of 25

Site installation handover

Complete

TRI125.CHK.008 Veefil-RT 175-S System Installation Checklist

and attach photos

of the installation.

5.1

Pre-checks

Check strain relief on power cables.

Check earths are attached on removable panels and doors.

Check if there is any remaining liquid or dust and clean the site.

5.2

Polarity, cross-wire and bolted short test

5.2.1

DC link test

Use a DMM and a long piece of wire to perform a continuity test between each of the
items in the following table:

User Unit

Power Unit

Pass Criteria

Earth

DC +

DC -

Earth

Connected

DC +

DC +

Connected

DC -

Earth

DC -

DC +

DC -

Connected

Earth

Summary of Contents for Veefil-RT 175-S


























Search results

Summary of Contents for Veefil-RT 175-S

Reviews:

Related manuals for Veefil-RT 175-S

Brands by name

Popular brands

Tritium Veefil-RT 175-S, Installation Manual

Search results

Summary of Contents for Veefil-RT 175-S

Reviews:

Related manuals for Veefil-RT 175-S

Brands by name

Popular brands