TRI tool BEVELMASTER 214B Page 7 Manual Download

Page: 7 / 58

Model 214B BEVELMASTER

92-1500 : Rev. 140425

SPECIFICATIONS

DESIGN AND OPERATING FEATURES

The lathe accepts its own torque through the mandrel.

The expanding mandrel provides fast, accurate self-centering and alignment.

The lathe, provided with a convenient handle, is lightweight and easily handled by

one operator.

Pipe weld end preparations that meet all existing conventional codes including the

more stringent nuclear codes may be machined using the Model 214B.

The various interchangeable jaw blocks, ramps and adapters will secure the Model

214B Pipe Beveler to pipe and tubing having an inside diameter ranging from 4”

(101.6 mm) through 14.08” (357.6 mm).

The expanding mandrel provides fast, accurate self-centering and alignment to the

pipe or tubing to be machined.

No additional restraining devices are required.

All 115V motors require a minimum of a 20-amp circuit.

The Tool is configured with an in-line feed knob and pneumatic drive motor at a right

angle to the lathe head.

Summary of Contents for BEVELMASTER 214B



























































Search results

Summary of Contents for BEVELMASTER 214B

Reviews:

Related manuals for BEVELMASTER 214B

Brands by name

Popular brands

TRI tool BEVELMASTER 214B, Manual

Search results

Summary of Contents for BEVELMASTER 214B

Reviews:

Related manuals for BEVELMASTER 214B

Brands by name

Popular brands