TRI tool BEVELMASTER 214B Manual Download | Manualshive

Page: 25 / 58

background image

25

Model 214B BEVELMASTER

®

92-1500 : Rev. 140425

After Machining Cleanup

Rotate the feed handle counterclockwise to separate the tool bit(s) from the

pipe.

Rotate the feed handle counterclockwise until the tool bit is approximately

1/8" (3 mm) away from the end of the pipe.

When the unit is operated in the vertical position, cutting head up, it should

be turned upside down and the chips and/or other debris removed after each

cutting operation has been completed.

Tool life may be severely shortened, unless chips and/or other debris

that have been deposited on the cutting head during the machining

operation are removed.

Loosen the Mandrel draw nut to release the mandrel from the pipe.

Slowly pull the Model 214B and the mandrel from the end of the pipe.

The mandrel assembly may be left in the Model 214B and installed as a

complete assembly in the next pipe to be machined.

«
...
23
24
25
26
27
...
»

Summary of Contents for BEVELMASTER 214B



























































Reviews:

No comments

Related manuals for BEVELMASTER 214B

Brand: Warren Controls Pages: 16

Brand: ABS Pages: 8

Brand: ?HC Pages: 2

Brand: Wacker Neuson Pages: 52

Brand: Paslode Pages: 32

Brand: Fein Pages: 95

Brand: Campbell Hausfeld Pages: 48

Brand: Campbell Hausfeld Pages: 36

Brand: Eriez Pages: 12

Brand: Parkside Pages: 65

Brand: Graco Pages: 54

Brand: Temper Pages: 19

Brand: RIDGID Pages: 2

Brand: Beta Pages: 88

Brand: Ferm Pages: 16

Brand: Chicago Pneumatic Pages: 36

Brand: Parkside Pages: 140

Brand: Fein Pages: 188

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands