TRI tool BEVELMASTER 214B Manual Download

Page: 9 / 58

Model 214B BEVELMASTER

92-1500 : Rev. 140425

Cutting Capacities

Basic Pipe Sizes

4" Pipe - Schedule 5 through 160

5" through 14" pipe - All schedules

Basic Tube Sizes

Up to 1.32" (33.4 mm) wall tubing with a maximum O.D. of 14.00"

(355.6 mm) and a minimum I.D. of 3.44" (87.4 mm) may be beveled

with standard mandrel.

Wall Thickness Capacity

Wall thickness of all standard pipe schedules 1.41" (35.7 mm)

maximum in the range listed. Tubing with greater wall thickness may

be handled provided the I.D. is greater than 3.44" (87.4 mm ) and the

O.D. is less than 14.00" (355.6 mm). Contact Tri Tool for heavier wall

procedures.

Counterboring Operations

The tool will counterbore pipe and tubing with an I.D. range of 3.44"

(87.4 mm) to 13.75" (330.2 mm).

Material Cutting Capability

Mild steels, chrome steels (Rc 35 max), stainless steel, copper-nickel alloys

and aluminum without limitations except size and wall thickness as specified.

Inconel and some other high temperature alloys may require special proce-

dures as a function of wall thickness and type of end preparation. Contact Tri

Tool’s Engineering Department for details.

Cutting Speeds

Maximum Head Speed: 20 rpm

Maximum Head H.P.: 10 rpm

Functional Head Range: 5 -20 rpm

Summary of Contents for BEVELMASTER 214B



























































Search results

Summary of Contents for BEVELMASTER 214B

Reviews:

Related manuals for BEVELMASTER 214B

Brands by name

Popular brands

TRI tool BEVELMASTER 214B, Manual

Search results

Summary of Contents for BEVELMASTER 214B

Reviews:

Related manuals for BEVELMASTER 214B

Brands by name

Popular brands