manualshive.com logo in svg

TRI tool BEVELMASTER 214B, Manual

Share
Download
TRI tool BEVELMASTER 214B Manual Download Page 15

15

Model 214B BEVELMASTER

®

92-1500 : Rev. 140425

Cutting Capacities

Basic pipe sizes

4" - Schedules 5 and 160

5" through 14" – All Schedules

Basic Tube Sizes

Up to 1.32" (33.5 mm) wall tubing with a maximum OD of 14.00" (355.6 

mm) and a minimum ID of 3.44" (87.4 mm) may be beveled with stan-

dard mandrel.

Wall Thickness Capacity

Wall thickness of all standard pipe schedules, 1.32" (33.5 mm) max-

imum, in the range listed.  Tubing with greater wall thickness may be 

handled provided the ID is greater than 3.44" (87.4 mm) and the OD is 

less than 14.00" (355.6 mm).  Contact TRI TOOL Inc. for heavier wall 

procedures.

Counterboring Operations

The tool will counterbore pipe and tubing with an ID range of 3.328" 

(84.6 mm) to 14.00" (355.6 mm).

Material Cutting Capabilities

Mild steels, chrome steels (Rc 35 max.), stainless steel, copper-nickel and 

aluminum without limitations other than size and wall thickness as specified.

Inconel and some other high-temperature alloys may require special proce-

dures as a function of wall thickness and type of end preparation.  Contact 

TRI TOOL’s Engineering Department for details.

Summary of Contents for BEVELMASTER 214B



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands