manualshive.com logo in svg

TRI tool BEVELMASTER 214B, Manual

Share
Download
TRI tool BEVELMASTER 214B Manual Download Page 21

21

Model 214B BEVELMASTER

®

92-1500 : Rev. 140425

NOTE:

Adjustment of Torque Acceptance Keys

Tighten the set screws to secure the tool bit(s) in the tool holder(s).

Adjust the counterbore tool bit radially to control counterbore diameter. 

Adjust the bevel tool bit radially to control the counterbore depth to the bevel 

relationship.

INSTALL THE MANDREL IN THE MODEL 214B

Slide the Model 214B gently onto the mandrel assembly until it comes to a solid stop 

against the torque acceptance keys.

Rotate the Model 214B as required to engage the torque acceptance keys with the 

slots in the mandrel shaft.

Since the mandrel shaft will contact the torque acceptance keys, before the 

feed nut engages the mandrel shaft threads, caution should be taken not to 

force (or allow) the machine to impact the lead threads of the feed nut with 

the lead threads of the mandrel.

ADJUSTMENT OF THE TORQUE ACCEPTANCE KEYS

Mandrel Shaft

Torque Acceptance Key

Cap Screw

Set Screw

Feed Housing

Summary of Contents for BEVELMASTER 214B



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands