TRI tool BEVELMASTER 214B Page 3 Manual Download

Page: 3 / 58

Model 214B BEVELMASTER

92-1500 : Rev. 140425

SAFETY PRECAUTIONS

WARNING:

IN GENERAL

When using rotating head cutting equipment, follow the safety recommendations in

this manual to reduce the risk of personal injury.

Operate this tool only in accordance with specific operating instructions.

Do not override the deadman switch on the power unit. Locking down, ob-

structing, or in any way defeating the deadman switch on the power drive unit

may result in serious injury.

DRESS CONSIDERATIONS

Use standard safety equipment. Hard hats, safety shoes, safety harnesses, protec-

tive clothes, and other safety devices should always be used when appropriate.

Use safety glasses. Do not operate cutting tools without eye protection.

Dress properly. Do not wear loose clothing or jewelry. They can be caught in rotat-

ing and moving parts. Avoid slippery floors or wear nonskid footwear. If you have

long hair, wear protective hair covering to contain it.

WORK AREA

Keep the work area clean. Keep the area well lit. Keep electrical cords, cables,

rags, rigging straps, and etc. clear of rotating equipment. Do not use power-cutting

tools in the presence of flammable liquids and gasses.

Keep visitors away. Do not let visitors or untrained personnel at or near operating

tools. Enforce eye protection requirements for all observers.

Do not over reach. Keep proper footing at all times.

Summary of Contents for BEVELMASTER 214B



























































Search results

Summary of Contents for BEVELMASTER 214B

Reviews:

Related manuals for BEVELMASTER 214B

Brands by name

Popular brands

TRI tool BEVELMASTER 214B, Manual

Search results

Summary of Contents for BEVELMASTER 214B

Reviews:

Related manuals for BEVELMASTER 214B

Brands by name

Popular brands