Tri-Star M100LFG-TT/150 Owner'S Manual Download Page 41 | Manualshive

Page: 41 / 73

Tri-Star M100LFG-TT/150 Owner'S Manual Download Page 41

41

Scanner Resolution

is used to determine the size of the message in inches. This value is based on

the type of scanner, focusing optics and the distance from the scanner to the wire.

Laser Com Port

specifies computer serial port numbers for laser connections.

Local IP Address

is the IP address of the supplied computer.

PLC IP Address

is the IP address of the PLC.

Printer IP Address and port

relate to the optional label printers.

Warm Up Time

is the amount of time after the diode is turned on before the laser is ready. The

diode turns on automatically when the machine powers up.

Conversion Factor

is used to convert the analog input from the laser power meter to Watts.

Laser Off Time

is the maximum time the laser can be idle before turning the diode pump off.

Click the

Save

button to save all these values to the application.

Click the

Cancel

button to close the dialog box without saving any changes

«
...
39
40
41
42
43
...
»

Summary of Contents for M100LFG-TT/150










































































Reviews:

No comments