background image

SLASH KIT • 3 

All of us at Traxxas want you to safely enjoy your new 

model. Operate your model sensibly and with care, and 

it will be exciting, safe, and fun for you and those around 

you. Failure to operate your model in a safe and responsible 

manner may result in property damage and serious injury. 

The precautions outlined in this manual should be strictly 

followed to help ensure safe operation. You alone must see 

that the instructions are followed and the precautions are 

adhered to.

Important Points to Remember

• Your model is not intended for use on public roads or 

congested areas where its operation can conflict with or 

disrupt pedestrian or vehicular traffic.

• Never, under any circumstances, operate the model in 

crowds of people. Your model is very fast and could cause 

injury if allowed to collide with anyone.

• Because your model is controlled by radio, it is subject to 

radio interference from many sources that are beyond your 

control. Since radio interference can cause momentary 

losses of radio control, always allow a safety margin in all 

directions around the model in order to prevent collisions.

• The motor, battery, and speed control can become hot 

during use. Be careful to avoid getting burned.

• Don’t operate your model at night, or anytime your line  

of sight to the model may be obstructed or impaired in  

any way.

Speed Control

Your model’s electronic speed control (ESC) is an extremely 

powerful electronic device capable of delivering high 

current. Please closely follow these precautions to prevent 

damage to the speed control or other components.
• 

Disconnect the Battery:

 Always disconnect the battery or 

batteries from the speed control when not in use. 

• 

Insulate the Wires:

 Always insulate exposed wiring with 

heat shrink tubing to prevent short circuits.

• 

Transmitter on First:

 Switch on your transmitter first before 

switching on the speed control to prevent runaways and 

erratic performance.

• 

Don’t Get Burned:

 The ESC and motor can become 

extremely hot during use, so be careful not to touch them 

until they cool. Supply adequate airflow for cooling.

• 

Use the Factory-Installed Connectors:

 Do not change the 

battery and motor connectors. Improper wiring can cause 

fire or damage to the ESC. Please note that modified speed 

controls can be subject to a rewiring fee when returned for 

service.

• 

No Reverse Voltage: 

The ESC is not protected against 

reverse polarity voltage. 

• 

No Schottky Diodes:

 External Schottky diodes are not 

compatible with reversing speed controls. Using a Schottky 

diode with your Traxxas speed control will damage the ESC 

and void the 30-day warranty.

• 

Always

 adhere to the minimum and maximum limitations 

of the speed control as stated in the specifications table in 

the Owner’s Manual. If your ESC operates on two batteries, 

do not mix battery types and capacities. Use the same 

voltage and capacity for both batteries. Using mismatched 

battery packs could damage the batteries and electronic 

speed control.

Recycling Traxxas Power Cell NiMH Batteries

Traxxas strongly encourages you to recycle Power Cell NiMH 

batteries when they reach the end of their useful life. Do 

not throw batteries in the trash. All Power Cell NiMH battery 

packs display the RBRC (Rechargeable Battery Recycling 

Corporation) icon, indicating they are recyclable. To find a 

recycling center near you, ask your local hobby dealer or visit 

www.call2recycle.org.

SAFETY PRECAUTIONS

Summary of Contents for SLASH 58014-4





































Reviews: