background image

2 • SLASH KIT

           

                                                          

Your model is able to use LiPo  

                           batteries. Charging and discharging batteries has the 

potential for fire, explosion, serious injury, and property damage if 

not performed per the instructions. Before use, read and follow all 

manufacturer’s instructions, warnings, and precautions. In addition, 

Lithium Polymer (LiPo) batteries pose a SEVERE risk of fire if not 

properly handled per the instructions and require special care and 

handling procedures for long life and safe operation. LiPo batteries 

are intended only for advanced users that are educated on the risks 

associated with LiPo battery use. Traxxas does not recommend 

that anyone under the age of 14 use or handle LiPo battery packs 

without the supervision of a knowledgeable and responsible adult. 

Dispose of used batteries according to the instructions.

Important Warnings for users of Lithium Polymer (LiPo) batteries:

• LiPo batteries have a minimum safe discharge voltage threshold 

that should not be exceeded. The electronic speed control is 

equipped with built-in Low-Voltage Detection that alerts the 

driver when LiPo batteries have reached their minimum voltage 

(discharge) threshold. It is the driver’s responsibility to stop 

immediately to prevent the battery pack from being discharged 

below its safe minimum threshold.

• Low-Voltage Detection is just one part of a comprehensive plan 

for safe LiPo battery use. It is critical to follow all instructions for 

safe and proper charging, use, and storage of LiPo batteries. Make 

sure you understand how to use your LiPo batteries. If you have 

questions about LiPo battery usage, please consult with your local 

hobby dealer or contact the battery manufacturer. As a reminder, 

all batteries should be recycled at the end of their useful life.

• ONLY use a Lithium Polymer (LiPo) balance charger with a balance 

adapter port to charge LiPo batteries. Never use NiMH or NiCad-

type chargers or charge modes to charge LiPo batteries. DO NOT 

charge with a NiMH-only charger. The use of a NiMH or NiCad 

charger or charge mode will damage the batteries and may cause 

fire and personal injury.

• NEVER charge LiPo battery packs in series or parallel. Charging 

packs in series or parallel may result in improper charger cell 

recognition and an improper charging rate that may lead to 

overcharging, cell imbalance, cell damage, and fire. 

• ALWAYS inspect your LiPo batteries carefully before charging. 

Look for any loose leads or connectors, damaged wire insulation, 

damaged cell packaging, impact damage, fluid leaks, swelling 

(a sign of internal damage), cell deformity, missing labels, or 

any other damage or irregularity. If any of these conditions are 

observed, do not charge or use the battery pack. Follow the 

disposal instructions included with your battery to properly and 

safely dispose of the battery. 

• DO NOT store or charge LiPo batteries with or around other 

batteries or battery packs of any type, including other LiPos.

• Store and transport your battery pack(s) in a cool dry place. 

DO NOT store in direct sunlight. DO NOT allow the storage 

temperature to exceed 140°F or 60°C, such as in the trunk of a car, 

or the cells may be damaged and create a fire risk. 

• DO NOT disassemble LiPo batteries or cells.
• DO NOT attempt to build your own LiPo battery pack from  

loose cells. 

Charging and handling precautions for all battery types:

• BEFORE you charge, ALWAYS confirm that the charger  

settings exactly match the type (chemistry), specification, and 

configuration of the battery to be charged. 

FIRE HAZARD!

WARNING!  CAUTION!  DANGER!

• DO NOT attempt to charge non-rechargeable batteries 

(explosion hazard), batteries that have an internal 

charge circuit or a protection circuit, batteries that have been 

altered from original manufacturer configuration, or batteries that 

have missing or unreadable labels, preventing you from properly 

identifying the battery type and specifications.

• DO NOT exceed the maximum manufacturer recommended  

charge rate.

• DO NOT let any exposed battery contacts or wires touch each 

other. This will cause the battery to short circuit and create the risk 

of fire.

• While charging or discharging, ALWAYS place the battery (all types 

of batteries) in a fire retardant/fire proof container and on a non-

flammable surface such as concrete.

• DO NOT charge batteries inside of an automobile. DO NOT charge 

batteries while driving in an automobile.

• NEVER charge batteries on wood, cloth, carpet, or on any other 

flammable material.

• ALWAYS charge batteries in a well-ventilated area.
• REMOVE flammable items and combustible materials from the 

charging area.

• DO NOT leave the charger and battery unattended while 

charging, discharging, or anytime the charger is ON with a battery 

connected. If there are any signs of a malfunction or in the event 

of an emergency, unplug the charger from the  power source and 

disconnect the battery from the charger.

• DO NOT operate the charger in a cluttered space, or place objects 

on top of the charger or battery.

• If any battery or battery cell is damaged in any way, DO NOT 

charge, discharge, or use the battery.

• Keep a Class D fire extinguisher nearby in case of fire.
• DO NOT disassemble, crush, short circuit, or expose the batteries 

to flame or other source of ignition. Toxic materials could be 

released. If eye or skin contact occurs, flush with water.

• If a battery gets hot to the touch during the charging process 

(temperature greater than 110°F / 43°C), immediately disconnect 

the battery from the charger and discontinue charging.

• Allow the battery pack to cool off between runs (before charging).
• ALWAYS unplug the charger and disconnect the battery when not 

in use. 

• ALWAYS unplug the battery from the electronic speed control 

when the model is not in use and when it is being stored or 

transported.

• DO NOT disassemble the charger.
• REMOVE the battery from your model or device before charging.
• DO NOT expose the charger to water or moisture.
• ALWAYS store battery packs safely out of the reach of children 

or pets. Children should always have adult supervision when 

charging and handling batteries.

• Nickel-Metal Hydride (NiMH) batteries must be recycled or 

disposed of properly.

• Always proceed with caution and use good common sense at all 

times.

SAFETY PRECAUTIONS

Summary of Contents for SLASH 58014-4





































Reviews: