32 • SLASH KIT
QUICK START GUIDE
The following guide is an overview of the procedures for getting your
model running. The complete manual for your model can be viewed
and downloaded by following the link on the cover of this manual or
by scanning the QR code. Please read this entire manual for complete
instructions on the proper use and maintenance of your model.
Read the Safety Precautions
For your own safety, understand where carelessness and misuse could
lead to personal injury and product damage.
Prepare Your Model
Selecting a charger and batteries for your model
Your model does not include a battery or charger. The speed control in
the model is compatible with both LiPo and NiMH batteries. One NiMH
or 2s LiPo battery equipped with a Traxxas High Current connector is
required. Traxxas Power Cell iD batteries are strongly recommended
for maximum performance and safer charging. The following chart lists
available Power Cell batteries for your model:
Make certain you choose the correct type of charger for the batteries you
select. Traxxas recommends you choose a genuine Traxxas EZ-Peak iD
charger for safer charging and maximum battery life and performance.
Install the battery pack in the model
Place the battery in the tray. Insert the
hold-down into the chassis as shown.
Secure by placing the clip into the post.
Compatible batteries:
• 6-7 cell NiMH • 2-cell LiPo
ATTENTION: USERS
OF LiPo BATTERIES
Activate Low-Voltage Detection when
using LiPo batteries. Refer to the EZ-Set
Tips card attached to your model, or see
the Electronic Speed Control Adjustments section of this guide.
Turning on Your Model
Turn on the transmitter
Always turn the transmitter on first, before turning on the model. The
transmitter’s LED will glow green.
Plug the battery into the speed control
Align the + and – markings. Make certain the battery plug is
completely inserted.
Turn on the model
Press and release the EZ-Set button on the speed control. The speed
control’s LED will glow.
Before Operating Your Model
Check servo operation
Confirm the model’s wheels turn right and left when the transmitter
steering wheel is turned right and left. The front wheels should be pointing
straight ahead. If they are turned slightly, slowly adjust the steering trim
control on the transmitter until they are pointing straight ahead.
Range test the radio system
With a friend’s help, check servo operation at the farthest distance you
plan to drive the model and confirm that there is no radio interference.
Operating Your Model
Forward
Neutral
Brake/Reverse
TURN
R
IG
H
T
T
U
R
N
LE
FT
LiPo Batteries with iD
2843X
5800mAh 7.4V 2-Cell 25C LiPo Battery
2869X
7600mAh 7.4V 2-Cell 25C LiPo Battery
NiMH Batteries with iD
2923X
Battery, Power Cell, 3000mAh (NiMH, 7-C flat, 8.4V)
2940X
Battery, Series 3 Power Cell, 3300mAh (NiMH, 7-C flat, 8.4V)
2950X
Battery, Series 4 Power Cell, 4200mAh (NiMH, 7-C flat, 8.4V)
Always turn your
transmitter on first.
Turn on the model.
1
1
2
2
Plug in the battery.
3
3
WARNING: FIRE HAZARD!
Users of Lithium Polymer (LiPo) batteries must read the
Warnings and Precautions beginning on page 2. You
MUST use a LiPo charger for LiPo batteries or battery damage
with the potential for fire will result.
Note: After stopping the model, return the transmitter’s trigger to
neutral and push up again to activate reverse throttle.
Charger
Part No.
NiMH
Compatible
LiPo
Compatible
Battery
iD
Max.
Cells
EZ-Peak Plus,
4 amps
2970
YES
YES
YES
3s
EZ-Peak Live,
12 amps
2971
YES
YES
YES
4s
EZ-Peak Dual,
8 amps
2972
YES
YES
YES
3s
EZ-Peak Live
Dual, 26+ amps
2973
YES
YES
YES
4s
Install batteries in the transmitter
The transmitter requires 4 AA alkaline or rechargeable batteries.
