Traxon ProPoint Vista 200W RGBW Installation Manual Download Page 15 | Manualshive

Page: 15 / 29

background image

www.traxontechnologies.com

©2020 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide

IG0108EN V0.1 08/20

P. 15 of 29

2.2 Pole Mount Installation (Vertical Mounting only)

Required Tools

200W Model

14mm and 17mm Hex Key

400W Model

14mm and 17mm Hex Key

Pole Mount Installation

FIG.13: ProPoint Vista pole Mount Installation

Preparation

•

Remove the ProPoint luminaire from the packaging and place the unit on a level surface.

Pole Mounting Steps

•

Mark the positions of the 4 mounting holes and then drill 4 x M12 holes with an electric drill. Mount the luminaire

bracket to the post mount plate using suitable M12 ﬁxings (e.g. M12 bolt, spring washer and locking M12 nut).

«
...
13
14
15
16
17
...
»

Summary of Contents for ProPoint Vista 200W RGBW






























Reviews:

No comments

Related manuals for ProPoint Vista 200W RGBW

SACE Tmax XT Series

Brand: ABB Pages: 11

Brand: Walker Bay Pages: 8

Brand: Latchways Pages: 80

Brand: Kapriol Pages: 28

Brand: Cameo Pages: 64

Brand: Cameo Pages: 100

Brand: CAME Pages: 32

Brand: Cameo Pages: 40

Brand: M-system Pages: 2

Brand: Rico Pages: 34

FlexDraper FD2 Series

Brand: MacDon Pages: 2

OXYGEN PRO MINI

Brand: M-Audio Pages: 56

Brand: Haas Pages: 12

Brand: SaMASZ Pages: 25

Brand: Balanced Body Pages: 4

Brand: Balanced Body Pages: 2

Reformer Trapeze Combination

Brand: Balanced Body Pages: 164

Brand: Wacker Neuson Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands