Transition Networks IONPS-D-R1 User Manual Download Page 43 | Manualshive

Page: 43 / 50

background image

Transition Networks, Inc.

IONPS-D-R1 User Guide

33707 Rev. A

https://www.transition.com

Page

43

of

50

Message

:

There are 2 power supplies in the chassis, you can not set both of them to slave mode!

Warning: IONPS-A/D-R1 operation mode is different from configured mode, you can not insert 2 slave mode
power supplies in chassis!
Meaning

: You tried to configure both IONPS-D-R1 power supplies as “Secondary” devices.

Recovery

:

1. Review the “

General Specifications

” section.

2. Re-configure one of the two IONPS-D-R1 devices as the “Primary” supply (see chapter

3. IONPS-D-R1 Software

Configuration

on page

17

.

Message

:

Error: Relay state can only be set on IONPS-A!

Meaning

: You tried to enter an unsupported command for this device.

Recovery

:

1. Try another command on this device.
2. Switch to another device (

go

command) and re-try the original command.

Message

:

Error: Cannot set IONPS-D-R1 fan control mode on this card!

Error: Cannot set IONPS-D-R1 operation mode on this card!
Error: only IONPS-D-R1 can run this command!
Fail to get IONPS-D-R1 fan control mode!
Fail to set IONPS-D-R1 fan control mode!
Fail to set IONPS-D-R1 fan speed!
Fail to set IONPS-D-R1 operation mode!
Meaning

: You misconfigured the IONPS-D-R1.

Recovery

:

1. Review chapter

4. IONPS-D-R1 Software Configuration

on page

2. Re-configure one or more of theIONPS-D-R1 parameters (see chapter

4. IONPS-D-R1 Software Configuration

on page

Message

:

IONPS-D-R1 fan speed is out of range, its range is 2500 - 8300!

Meaning

: You misconfigured the IONPS-D-R1 fan speed.

Recovery

:

1. Re-configure the IONPS-D-R1 fan speed.
2. See

Power Supply Config – Web Method

on page

«
...
41
42
43
44
45
...
»

Summary of Contents for IONPS-D-R1



















































Reviews:

No comments

Related manuals for IONPS-D-R1

Brand: Oasser Pages: 29

Brand: Makita Pages: 14

Brand: PELA Pages: 8

Brand: Far Tools Pages: 33

Brand: Mafell Pages: 75

Brand: Mafell Pages: 46

Brand: Palmgren Pages: 20

Brand: TMG Pages: 19

NEWMAR Sentinel

Brand: Mission Critical Pages: 28

Brand: VOLTEQ Pages: 5

EPSITRON 787-712

Brand: WAGO Pages: 2

Brand: Ancor Pages: 12

Brand: Silverline Pages: 2

Brand: Hama Pages: 56

Brand: Neilsen Pages: 10

Brand: BK Precision Pages: 92

Brand: Jet Pages: 32

Brand: Hama Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands