Transition Networks IONPS-D-R1 User Manual Download | Manualshive

Page: 29 / 50

background image

Transition Networks, Inc.

IONPS-D-R1 User Guide

33707 Rev. A

https://www.transition.com

Page

29

of

50

IONPS-D-R1 CLI Messages

Error: Cannot set IONPS-A/D-R1 operation mode on this card!
Error: Cannot display card information on this module!
Error: Software version of this card is too old, please upgrade it!
Error: System is busy, please retry this command later!
Error: only IONPS-A/D-R1 can run this command!

Cannot set slot power on this card!

Failed to get IONPS-A/D-R1 operation mode!
Failed to get IONPS-A/D-R1 configure mode!
Failed to get IONPS-A/D-R1 fan control mode!

% There is no matched command.
% Command incomplete.

Error: Please change to power supply slot first before showing its configuration!

Warning: IONPS-A/D-R1 operation mode is different from configured mode, you cannot insert 2 Secondary
mode IONPS-A/D-R1s in chassis!

Error: Relay state can only be set on IONPS-A, IONPS-D, and IONPSDCR1!

Error: this command should be executed on a relay!
Error: this command should be executed on a sensor!
Error: this command should be executed on an ION power supply!

The Operation Mode cannot be set as Slave on both power supplies!

Log user out if idle (inactive) for 15 minutes and display “

You are now logged out.

".

«
...
27
28
29
30
31
...
»

Summary of Contents for IONPS-D-R1



















































Reviews:

No comments

Related manuals for IONPS-D-R1

Brand: National Flooring Equipment Pages: 44

Brand: UHV Design Pages: 56

Brand: Icom Pages: 2

Brand: K&M Pages: 4

Brand: F.F. Group Pages: 36

Brand: REAC Pages: 15

Brand: Cleco Pages: 16

Brand: MAIMAN ELECTRONICS Pages: 24

Brand: Radio Shack Pages: 13

Brand: Metabo Pages: 68

Brand: InWin Pages: 15

WOOD MILL G9959

Brand: Grizzly Pages: 52

Brand: HORN'UP Pages: 20

Brand: Jarvis Pages: 12

Brand: Bomag Pages: 58

Brand: BSM Pages: 96

Brand: Farnell Pages: 15

Muyang SZLH Series

Brand: Famsun Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands