manualshive.com logo in svg

Tradinco TRAQC-7, User Manual

Share
Download
Tradinco TRAQC-7 User Manual Download Page 7

User Manual

 

TRAQC-8  

 

TRAQC-8 04/2017 EN Rev.4

 

 

  

page : 7 

1.2.3

 

CE Electrical Safety Directive 2014/35/EU 

The electrical part of the TRAQC-8 (pressure calibrator of the Tradinco Traqc-7 series) meets 
the regulations as mentioned standards  
EN 61010-1 : 2010 
 

•

 

The unit is CE marked accordingly  

 

1.3

 

 Symbols Used 

 
Warning for conditions or practices that could result in personal injury, loss of life and/or 
in damage to the product or other property. 
 

 
 

Attention signal or remark 

 
 

1.4

 

Scope of this manual 

This manual contains information for instruments built after Oktober 2015 with firmware revision 
2.343 or higher. 
This manual is a user manual on how to operate the instrument; it is not a calibration instruction 
manual.  
 
As  Tradinco  Instruments  continuously  strives  to  improve  its  products,  specifications  of 
instruments may be altered without further notice. 

Summary of Contents for TRAQC-7











































Reviews:

No comments

Brands by name

Popular brands

Load more brands