manualshive.com logo in svg

Tradinco TRAQC-7, User Manual

Share
Download
Tradinco TRAQC-7 User Manual Download Page 13

User Manual

 

TRAQC-8  

 

TRAQC-8 04/2017 EN Rev.4

 

 

  

page : 13 

2.6

 

Power Supply 

The unit is equipped with an internal not removable Li-Ion battery. The charging of the batteries 
is fully automated. The TRAQC-8 is charged when its connected to the mains power supply 
charging will start as soon as the instrument is connected to the mains supply. 
The instrument can be used while charging the battery, but the required charging time could be 
increased depending upon the selected operating mode of the instrument. 
 

2.6.1

 

Battery status display 

The status of the battery is displayed with a battery symbol on the lcd display when the 
instrument is switched on. 
During charging the battery symbol will be filled with lines until it is completely filled and when 
all lines are drawn the symbol will be cleared and starts filling again. 
When charging is completed the symbol will be completely filled and remains filled as long as 
the instrument is connected to the mains supply. 
 
 
 
 

2.6.2

 

Operating time indication 

The instrument has an internal ‘gas gauge’ to measure the battery capacity, this ga

s gauge is 

automatically updated when the battery is charged or discharged and is used to indicate the 
battery charging state and remaining operating time. 
The charging state of the battery is indicated with lines in the battery symbol. 
When the battery is full all lines in the battery are drawn and when the instrument is operating 
on the battery less lines will be shown. 
The number of lines shown in the battery is a rough indication of the remaining battery 
capacity.  
When the remaining operating time drops below 3 hours the remaining time will be shown next 
to the battery symbol 
 

 The operating time of the instrument on the indicated charge state depends upon the 
usage of the instrument, Operating modes where the electrical outputs are used draw 
more current from the battery and therefore shorten the operating time more than other 
modes. 

 
 

2.6.3

 

Instrument charging before storage 

The instrument should not be stored for longer periods with an empty battery, doing so will 
reduce the capacity of the battery and shorten the battery life. 
When the instrument must be stored the battery should be charged to at least 50% of its 
indicated capacity. 
 
 

2.6.4

 

Battery Replacement 

The battery can only be replaced by Tradinco or a Tradinco approved repair facility. 
 

Summary of Contents for TRAQC-7











































Reviews:

No comments

Brands by name

Popular brands

Load more brands