Toyota PZQ90-89011 Installation Manual Download Page 66

Page: 66 / 68

Page

66/68

Rear Camera Connection

For vehicle with 2011 Display Audio (PZQ60-00521, PZQ60-00525) or 2011 AVN (PZQ60-00531,
PZQ60-00535)

Connect the rear camera 4 pin connector to the back
of the audio unit as shown.

NOTE:

To show the reverse display on the screen, reverse
signal need to be connected using PZQ60-00151
harness.

For August 2013 production vehicle onward vehicle

Using

Hilux Camera Patch Wire Harness

(PZQ60-00230)

connect the pre-wire rear camera

connector (4pin female) to the 4pin male connector
of the wire harness.

For AVN/DADLX

For DA Base

Disconnect the original line fit 24 pin connector
harness and cable tie the connector to the existing
vehicle harness. Please see the 24 pin connector
position on the left audio diagram.

Replace the existing vehicle 24 pin connector with
the

Hilux Camera Patch Wire Harness

(PZQ60-00230)

Summary of Contents for PZQ90-89011





































































Search results

Summary of Contents for PZQ90-89011

Reviews:

Related manuals for PZQ90-89011

Brands by name

Popular brands

Toyota PZQ90-89011, Installation Manual

Search results

Summary of Contents for PZQ90-89011

Reviews:

Related manuals for PZQ90-89011

Brands by name

Popular brands