manualshive.com logo in svg

Toyota 1NZ-FE, User Manual

Share
Download
Toyota 1NZ-FE User Manual Download Page 52

ENGINE - 1NZ-FE ENGINE

00REG26Y

D13N26

Atmosphere

Purge VSV
(OFF)

ECM

Canister Pump Module

Vent Valve
(OFF)

M

Leak Detection 
Pump & Pump 
Motor

P

Canister Pressure
Sensor

Reference Orifice

Purge VSV

ON (Open)

OFF (Close)

ON

OFF (Vent)

Vent Valve

ON

OFF

Pump Motor

Atmospheric Pressure

System Pressure

0.02 in. Pressure

0.02 in. Pressure Measurement

EG-53

c. 0.02 in. Leak Pressure Measurement

1) The vent valve remains off, and the ECM introduces atmospheric pressure into the canister and

actuates the leak detection pump in order to create a negative pressure.

2) At this time, the pressure will not decrease beyond a 0.02 in. pressure due to the atmospheric pressure

that enters through a 0.02 in. diameter reference orifice measuring 0.5 mm (0.02 in.).

3) The ECM compares the logic value and this pressure, and stores it as a 0.02 in. leak pressure in its

memory.

4) If the measurement value is below the standard, the ECM will determine that the reference orifice

is clogged and store DTC (Diagnostic Trouble Code) P043E in its memory.

5) If the measurement value is above the standard, the ECM will determine that a high flow rate pressure

is passing through the reference orifice and store DTCs (Diagnostic Trouble Codes) P043F, P2401,
P2402, and P2422 in its memory.

Summary of Contents for 1NZ-FE




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands