manualshive.com logo in svg

Toyota 1NZ-FE, User Manual

Share
Download
Toyota 1NZ-FE User Manual Download Page 10

ENGINE - 1NZ-FE ENGINE

171EG14

Camshaft Timing
Oil Control Valve

VVT-i
Controller

Chain
Tensioner

Oil Pump

Oil Strainer

Oil Filter

171EG15

Main Oil Hole

Crankshaft
Journal

Oil Filter

Relief
Valve

Connecting
Rod

Oil Pump

Oil Jet

Oil Strainer

Piston

Oil Jet

Cylinder Head

Camshaft Timing
Oil Control Valve
Filter

Chain
Tensioner

Timing Chain

Intake
Camshaft
Journal

Exhaust
Camshaft
Journal

Camshaft Timing
Oil Control Valve

VVT-i

Oil Pan

EG-11

LUBRICATION SYSTEM

1. General

The lubrication circuit is fully pressurized and oil passes through an oil filter.

A trochoid gear type oil pump, which is driven directly by the crankshaft, is provided in the front of the
cylinder block.

The oil filter is installed diagonally downward from the side of the cylinder block to realize excellent
serviceability.

The intake camshaft is provided with a VVT-i controller, and cylinder head is provided with a camshaft
timing oil control valve. This system is operated by the engine oil.

 Oil Capacity 

Liter (US qts, Imp qts)

Dry

4.1 (4.3, 3.6)

with Oil Filter

3.7 (3.9, 3.3)

without Oil Filter

3.4 (3.6, 3.0)

 Oil Circuit 

Summary of Contents for 1NZ-FE




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands